Filter Bio-Media Planner

Your tank’s water volume — use the Tank Volume Calculator if you are unsure
Weigh a day’s food on a kitchen scale — a guess here gives a guessed answer
Effective surface from the AquaInfo table — foam holds far more surface per litre than lava rock or Matrix
The media space inside your filter, after baskets and equipment — for the 50–60% allowance check
Rough total weight of your stock — for the Aquarium Science surface planning estimates only

Model A — label dose: 250 mL of Matrix per 200 L of water (Seachem Matrix label). Model B — feed-based: 0.03 m² of bio-media surface per gram of feed per day. Per-media surface figures are the AquaInfo table of effective surface area (ft²/ft³, converted to m²/L). The 5 ft² per lb of fish (ammonia oxidation) and 100 ft² per lb (crystal clear water) figures are Aquarium Science planning estimates, never guarantees. The 50–60% figure is a planning allowance: bio-media is roughly 50–60% of the filter’s usable media volume. This tool plans media volume, not filter flow — flow is the Heater & Filter Sizer’s job.

How much bio-media do you need?

Enter your tank volume in litres — the label dose appears here, with the feed-based figure and the allowance check when you add them.

Why use this calculator?

  • See two honest models side by side — a product-label dose and a feed-based figure — instead of one unexplained “required” volume.
  • Find out how many litres of your chosen media the feed load points to, using verified effective surface-area figures.
  • Check whether the media fits the 50–60% planning allowance for your filter’s usable media volume.
  • Know what the numbers cannot tell you — only ammonia and nitrite testing shows whether the filter copes.

Size the filter’s flow with the Heater & Filter Sizer, find your tank’s volume with the Tank Volume Calculator, or work out daily feeding with the Feeding Calculator. · Back to Tank Size & Setup

Enter your tank volume, daily feed and media type — get the bio-media volume your filter needs, from two honest models side by side: a product-label dose and a feed-based figure. Everything runs in your browser; nothing is saved.

How it works

Model A — label dose (primary, simplest). The Seachem Matrix label says 250 mL of Matrix for each 200 L (50 US gallons) of water. So a 200 L tank takes 250 mL by the label. Note the conflict, flagged not resolved: some pages quote the older wording of 500 mL per 200 L. This tool uses the current 250 mL figure and says so; if your packaging says 500 mL, follow your packaging.

Model B — feed-based. 0.03 m² of bio-media surface per gram of feed per day (MyAquaponics feed-based calculator; Chen, Ling & Blancheton 2006, via the research report). A planning figure, not a manufacturer spec. Weigh a day's food on a kitchen scale — a guess here gives a guessed answer.

Per-media surface. The litres conversion uses the AquaInfo "8.8. Filter and Media Design for Aquariums" table of effective surface area (ft² per ft³, converted to m² per litre: m²/L = ft²/ft³ × 0.092903 ÷ 28.3168). Only loose media from that table are offered. Omitted on purpose: fluidized K1 (540 ft²/ft³) — the table itself warns its figure is per cubic foot of filter, not per cubic foot of media, so it cannot be converted the same way; air / powerhead sponge and undergravel figures — whole-filter setups, not media bought by the litre; Blue Matala pads — sheet media, not loose volume.

Two more conflicts, flagged not resolved. The same AquaInfo site elsewhere says Matrix has "roughly 15 to 30 ft²/ft³ of effective surface area, confirmed by testing under actual aquarium conditions", while its table gives Matrix 60 ft²/ft³. Seachem's own marketing claims over 700 m²/L for Matrix — that counts internal micropore area, not the effective surface in the AquaInfo table, and is not the figure used here. The table value (60) is used, and labelled as the table value.

Planning allowance and estimates. Bio-media should be roughly 50–60% of the filter's usable media volume, leaving room for mechanical media and flow — an allowance from the research report, not a law. Aquarium Science planning estimates: very roughly 5 sq ft of media surface per lb of fish for ammonia oxidation, and about 100 sq ft per lb for "crystal clear" water. Planning estimates only, never guarantees.

What it does not do. This tool plans media volume. It is distinct from the Heater & Filter Sizer, which sizes filter flow. Neither model is a guarantee — ammonia and nitrite testing is the real check, and more media is not a substitute for stocking sense.

Worked example

A 200 L tank, 5 g of feed a day, Seachem Matrix, 1 L of usable media volume, 1 lb of fish.

Inputs

Tank 200 L. Feed 5 g/day. Media Matrix. Usable volume 1 L. Fish 1 lb.

Formula

Model A: 250 mL per 200 L. Model B: 0.03 m² per g of feed per day. Matrix: 60 ft²/ft³ = 0.197 m²/L.

Calculation

Model A: 200 ÷ 200 × 250 = 250 mL (0.25 L). Model B: 5 × 0.03 = 0.15 m² of surface. As Matrix: 0.15 ÷ 0.197 = 0.76 L. Allowance: 50–60% of 1 L = 0.5–0.6 L; the 0.25 L label dose sits inside it.

Result

250 mL by the label, 0.76 L of Matrix by the feed model — plan around the range between the two, not a single "required" volume. Fish estimates: 5 ft² for ammonia oxidation, 100 ft² for "crystal clear" water.

When the two models disagree, that is the honest range to plan around. Here the feed model points higher than the label dose — which is normal when the feeding load is the bigger driver. If the label dose had been the higher one, the range would run the other way.

How to read your results

The verdict word is the label dose in mL — Model A, the simplest starting point. Under it, the pair line names the tank it was worked out for. The stat grid covers both models: the label dose, the feed-based surface (or a dash if you entered no feed), and the litres of your chosen media that surface converts to (or a dash if you picked no media).

The rows then work through the checks: the media conversion, the 50–60% allowance against your filter's usable volume (a Needs action if the label dose sits above it), the fish-weight surface estimates, and the two cautions that matter most — more media is not a substitute for stocking sense, and manufacturer surface-area claims are not the same as effective surface.

What to do next: compare the two models, pick the media, and test ammonia and nitrite after stocking or after changing media — only the tests show whether the filter copes.

Common mistakes

  • Chasing the marketing surface number. Seachem markets Matrix at over 700 m²/L of internal pore area; the effective surface under aquarium conditions in the AquaInfo table is 60 ft²/ft³. This tool uses the table figure.
  • Packing the canister full of bio-media. Bio-media is roughly 50–60% of the usable media volume — the rest is mechanical media and space for flow.
  • Using the label dose for a different media. The 250 mL per 200 L dose is the Matrix label; other media convert through their own surface figures.
  • Guessing the daily feed. Weigh a day's food on a kitchen scale — the feed model is only as good as the feed number.
  • Skipping the ammonia and nitrite tests. No number here proves the filter copes — the tests are the check.
  • Confusing media volume with filter flow. This tool plans how much media; how many times the tank turns over per hour is the Heater & Filter Sizer's job.
  • Treating the 5 ft² and 100 ft² per lb figures as guarantees. They are Aquarium Science planning estimates, never guarantees.

Effective surface by media

Effective surface area from the AquaInfo table, and the m² per litre this tool converts with (ft²/ft³ × 0.092903 ÷ 28.3168). Foam holds far more surface per litre than lava rock or Matrix.

MediaSurfacem² per L
30 PPI foam340 ft²/ft³1.115
Plastic pot scrubbers280 ft²/ft³0.919
20 PPI foam260 ft²/ft³0.853
Static K1 media260 ft²/ft³0.853
Bio balls100 ft²/ft³0.328
1/8 in pumice or perlite100 ft²/ft³0.328
Alfagrog80 ft²/ft³0.262
1/2 in lava rock60 ft²/ft³0.197
Seachem Matrix60 ft²/ft³0.197
Biohome Ultimate40 ft²/ft³0.131
Ceramic rings40 ft²/ft³0.131
Ceramic balls30 ft²/ft³0.098
Expanded clay pebbles30 ft²/ft³0.098

Fluidized K1, sponge filters, undergravel plates and Matala pads are omitted on purpose — their figures are per cubic foot of filter or whole-filter setups, not per litre of loose media. The Matrix figure is the table value (60 ft²/ft³); the same site elsewhere quotes 15–30 ft²/ft³, and Seachem's marketing claims over 700 m²/L of internal pore area.

FAQ

Which model should I trust — the label dose or the feed-based figure?

Both, as a range. The label dose is the simplest starting point; the feed model follows your actual feeding load. When they disagree, plan around the range between them, not a single "required" volume.

Why is the Matrix label 250 mL per 200 L here when some pages say 500 mL?

Some pages quote the older label wording of 500 mL per 200 L. This tool uses the current 250 mL figure, from retailer copies of the current label. If your packaging says 500 mL, follow your packaging.

Why does foam beat Matrix on surface per litre?

Because the table measures effective surface under aquarium conditions, not internal micropore area. Foam's open structure gives 340 ft²/ft³; Matrix's table figure is 60 ft²/ft³ — even though Seachem markets Matrix at over 700 m²/L of internal pore area.

Can I just fill the whole filter with bio-media?

No — bio-media is roughly 50–60% of the usable media volume as a planning allowance. The rest is mechanical media and space for flow. A filter packed solid flows badly no matter how much media is in it.

How much should I feed for the feed model?

Weigh a day's food on a kitchen scale and enter the grams. A guessed feed number gives a guessed answer — and overfeeding is the load the filter has to cope with.

Does more media mean I can stock more fish?

No. More media is not a substitute for stocking sense — a filter packed with media but fed far beyond its load still shows ammonia. Feed less, stock lighter, or add a second filter.

Sources

  1. Seachem Matrix label — 250 mL per 200 L, from retailer copies of the current label — aquariumsindia.com and abyssaquatics.co.uk (Manufacturer).
  2. AquaInfo — "8.8. Filter and Media Design for Aquariums", table of effective surface area — aquainfo.nl (Hobby practice).
  3. MyAquaponics — sizing a biofilter, feed-based: 0.03 m² per gram of feed per day — myaquaponics.co.za (Hobby practice).
  4. Chen, Ling & Blancheton (2006) — feed-based biofilter sizing, via the research report. No URL is on file for this source; it is listed by name. (Peer-reviewed).

Related tools