Pond Volume Calculator

Units
For a kidney shape, the longest point
Measure at several spots and average them

Volume is length × width × average depth (× 7.48 gallons per cubic foot). A kidney shape has no exact box formula — average the longest/widest and narrowest measurements and treat the result as an estimate. The liner size adds 2 ft of overlap on each side; the pump turns a fish pond over once per hour.

How many gallons — and what liner and pump?

Enter the pond measurements — the volume in gallons and litres, the liner size and the pump size appear here.

Why use this calculator?

  • Size the liner and pump before digging — not after the hole is the wrong shape.
  • Know the real volume for dosing and stocking: treatments are dosed per gallon, and a guessed volume is the usual reason a dose is wrong.
  • No mid-build surprises — buy the liner once, in the right size.

Once you have the gallons, size the pump and filter for the same water with the Heater & Filter Sizer, or check the water itself with the Water Parameter Checker. · Back to Tank Size & Setup

Work out a pond's volume in gallons and litres, the liner size to buy, and the pump size to run it — for rectangular, circular and kidney-shaped ponds, in feet or metres. Size the liner and pump before digging, not after the hole is the wrong shape. Everything runs in your browser; nothing is saved.

How it works

Volume. A rectangular pond is length × width × average depth. A circular pond is π × radius² × average depth, where the radius is half the diameter you enter. A kidney or irregular pond has no exact box formula: enter the average length (the average of the longest and narrowest) and the average width the same way, and treat the result as an estimate. Cubic feet become US gallons at 7.48052 gallons per cubic foot; litres are gallons × 3.78541. In metres, the measurements are converted to feet first (1 m = 3.28084 ft).

Liner. The liner must climb out of the hole, over the edge and anchor in a trench, so it is bigger than the pond: liner length = pond length + 2 × depth + 2 ft of overlap on each side, and the same for width. For a circular pond the liner is square, based on the diameter. Buy the next size up if the figure falls between stock sizes.

Pump. A fish pond turns over once per hour — the pump moves the whole volume every hour, so the pump size in gallons per hour (GPH) is the volume in gallons. A planted water garden with few or no fish can run about half that, one turnover every two hours. Always check the pump's flow at your real head height — the height the water is actually lifted — not its zero-head headline rating, which is measured with no lift at all.

Waterfall. If the pump also feeds a waterfall, add roughly 100 GPH per inch of spillway width on top of the turnover number.

Worked example

A rectangular fish pond, 10 × 8 ft, 2 ft deep on average.

Inputs

Rectangular · Fish pond · Length 10 ft · Width 8 ft · Average depth 2 ft.

Formula

Volume = L × W × depth × 7.48052 gal/ft³. Liner = length + 2 × depth + 4 ft. Pump = volume × 1 turnover/hour.

Calculation

10 × 8 × 2 = 160 ft³. 160 × 7.48052 = 1,196.9 gal. Litres = 1,196.9 × 3.78541 = 4,531 L. Liner = 10 + 4 + 4 = 18 ft by 8 + 4 + 4 = 16 ft.

Result

1,197 US gallons (4,531 L) · liner about 18.0 × 16.0 ft (5.5 × 4.9 m) · pump at least 1,197 GPH.

The other shapes follow the same steps. Circular, 10 ft diameter, 2 ft deep: π × 25 × 2 = 157.08 ft³ × 7.48052 = 1,175.0 gallons, with a square 18.0 × 18.0 ft liner. Kidney, averaging 12 × 8 ft and 2.5 ft deep: 12 × 8 × 2.5 = 240 ft³ = 1,795 gallons, liner 21.0 × 17.0 ft. Metric, 3 × 2 × 0.6 m: 3.6 m³ = 951 gallons.

How to read your results

The verdict is the volume in US gallons — the number to dose and stock by. Under it, the pond shape and type are named, and the stat grid shows the volume in litres and the pump size in GPH, with the turnover rate it is based on.

Below the stats, the checks are grouped. The OK rows give the liner size in feet and metres (with the 2 ft overlap rule behind it), the dosing reminder, and the waterfall allowance. A Caution row appears for a kidney pond: the volume is an estimate, so round the liner and pump up, not down — the fix underneath says the same thing. A slightly oversized liner or pump is cheap insurance against a short liner or a slow turnover.

Use the gallon number for dosing and stocking. Treatments are dosed per gallon, and a guessed volume is the usual reason a dose is wrong.

Common mistakes

  • Measuring depth in one spot. Ponds slope — shallow at the edges, deep in the middle. Measure at several spots and average them; a single deep reading overstates the volume.
  • Treating a kidney volume as exact. A kidney shape has no exact box formula. Average the longest and narrowest measurements, treat the result as an estimate, and round the liner and pump up.
  • Buying a liner the size of the pond. The liner has to climb out of the hole, over the edge and into an anchor trench — it needs the depth plus 2 ft of overlap on every side, or it will not reach.
  • Sizing the pump by its headline rating. A pump's headline GPH is its zero-head flow, with no lift. Check the flow at your real head height — the height the water is actually lifted to the filter or waterfall.
  • Running a fish pond on water-garden turnover. A planted water garden with few or no fish can run one turnover every two hours, but a fish pond needs the full volume every hour — half that rate leaves fish waste standing.
  • Guessing the volume for a dose. Treatments are dosed per gallon, and a guessed volume is the usual reason a dose is wrong. Measure the pond and calculate it.
  • Forgetting the waterfall. If the pump also feeds a waterfall, add roughly 100 GPH per inch of spillway width on top of the turnover number.

Common pond sizes

Rectangular fish ponds, with liner and pump sizes from this calculator's formulas. Liner is length + 2 × depth + 4 ft on each side; pump is one turnover per hour.

Pond L × W × depth (ft)Cubic feetVolume (US gal)Liner (ft)Pump (GPH)
6 × 4 × 1.53626913.0 × 11.0270
8 × 6 × 29671816.0 × 14.0719
10 × 8 × 21601,19718.0 × 16.01,197
12 × 8 × 2.52401,79521.0 × 17.01,796
15 × 10 × 34503,36625.0 × 20.03,367
20 × 12 × 37205,38630.0 × 22.05,386

FAQ

How do I measure the average depth?

Measure the depth at several spots — the shallow edges, the middle and the deep end — and average them. A pond that is 1 ft at the edges and 3 ft in the middle is 2 ft on average, not 3 ft. One deep reading overstates the volume; one shallow reading understates it.

How much liner overlap do I need?

Two feet of overlap on each side, on top of the depth: liner length = pond length + 2 × depth + 4 ft, and the same for width. The extra liner climbs out of the hole, over the edge and anchors in a trench around the pond. If the figure falls between stock sizes, buy the next size up.

What size pump do I need?

For a fish pond, a pump that moves the whole volume once per hour — so a 1,197-gallon pond needs at least 1,197 GPH. Check the flow at your real head height, not the zero-head rating on the box, and add roughly 100 GPH per inch of spillway width if the pump also feeds a waterfall.

Fish pond vs water garden — what is the difference?

The turnover rate. A fish pond turns over once per hour because fish produce waste that has to be moved through the filter. A planted water garden with few or no fish can run about half that — one turnover every two hours. Pick the pond type above and the calculator uses the right rate.

Can I use it for a round pond?

Yes — pick Circular and enter the diameter as the width. The volume is π × radius² × average depth, and the liner comes out square, based on the diameter. The length field is not used for a circular pond.

What about a kidney or irregular shape?

Pick Kidney and enter the average length and average width — the average of the longest and narrowest measurements in each direction — with the average depth. The result is an estimate, not an exact volume, so round the liner and pump up rather than down.

Sources

  1. NIST Special Publication 811 — 1 cubic foot = 7.48052 US gallons; 1 US gallon = 3.78541 L (Standard).
  2. Kendisco — Pond Pump sizing guide: size a pond pump to turn the entire volume over roughly once an hour (Hobby practice). kendisco.com/blog/pond-pump/
  3. PondHaven — Pond pump sizing: turn the pond's volume over about once an hour (Hobby practice).
  4. Fountain Depot — Pond circulation: circulate the entire pond at least once per hour (Hobby practice).
  5. Goldgage — Pond Filtration 101: a planted water garden with few or no fish can run about half the fish-pond turnover, one turnover every two hours (Hobby practice).

Related tools