Enter your dip water volume and the dose on your product label, and get the exact dose in millilitres and drops for your dip container. Math only — this never recommends a product, a concentration or a dip time; all of those come from your label. For very small doses, measure with a 1 mL syringe — droppers vary. Everything runs in your browser; nothing is saved.
How it works
Dose (mL) = label dose × (dip volume ÷ label volume). It is a direct proportion: if your container holds half the water the label dose is written for, you use half the dose. The tool converts every volume to litres first — 1 US gal = 3.78541 L, 1 US cup = 0.2365882 L — so gallons, litres and cups mix freely.
Drops = mL × 20. Twenty drops per millilitre is the standard dropper approximation for water-like liquids. It is an approximation: droppers vary, which is why doses under 1 mL belong in a 1 mL syringe, not in a counted drip.
The label dose can be in millilitres or drops. A label written in drops is converted to millilitres first (drops ÷ 20), then scaled the same way. Dip time is never calculated — it comes from the product label.
Worked example
A pest dip in 1 US gallon of dip water, at a label dose of 1 mL per gallon.
Dip water 1 US gal (3.785 L). Label dose 1 mL per 1 US gal (3.785 L).
Dose = label dose × (dip volume ÷ label volume). Drops = mL × 20.
Ratio = 3.785 ÷ 3.785 = 1.0. Dose = 1 × 1.0 = 1.00 mL. Drops = 1.00 × 20 = 20 drops.
1.00 mL, about 20 drops — timed per the product label, never longer.
A smaller case: 2 litres of dip water at a label dose of 1 mL per 4 litres. Ratio = 2 ÷ 4 = 0.5, so the dose is 1 × 0.5 = 0.50 mL, about 10 drops — under 1 mL, so use a 1 mL syringe. And a label in drops: 10 drops per gallon in half a gallon is 10 × 0.5 = 5 drops (0.25 mL).
How to read your results
The big number is the dose in millilitres, with the drop count beside it. The stat grid shows the dose, the drops, and the ratio — dip volume divided by label volume — so you can check the scaling at a glance. A ratio of 1.0 means your container matches the label volume exactly; 0.5 means half of it.
Read the rows under the verdict. "Caution" under 1 mL means reach for the syringe. "Caution" on the dip itself means: dip in display-tank water at tank temperature and salinity, time it per the label, and dispose of the used dip down the drain — never into the sump.
If the result looks wrong, check the volume first. The dose is only as good as the water you measured — a guessed container volume is the most common error on this page.
Common mistakes
- Guessing the dip water volume. Measure it with a jug — the dose scales exactly with the water, so a guessed volume is a wrong dose.
- Making a stronger dip "to be safe". Overdosing can burn tissue or kill the coral. The label dose is the dose.
- Leaving corals in longer than the label says. Time it per the label — many pest dips run 5–15 minutes — and do not leave corals in longer.
- Pouring used dip into the sump. Dispose of it down the drain and rinse anything it touched.
- Counting drops for a very small dose. Under 1 mL, droppers vary too much — a 1 mL syringe is more accurate.
- Dipping in fresh water or water at the wrong temperature. Dip in display-tank water at tank temperature and salinity.
- Treating a dip as a diagnosis. A dip scales a label dose for pests; it does not tell you what is wrong with a sick coral — for that, see an aquatic veterinarian.
Dose by dip volume (label 1 mL per gallon)
What the tool gives for each dip volume at a label dose of 1 mL per US gallon. Drops are rounded to whole drops.
| Dip water | Dose (mL) | Drops |
|---|---|---|
| 1 L | 0.26 | 5 |
| 2 L | 0.53 | 11 |
| 0.5 US gal | 0.50 | 10 |
| 1 US gal | 1.00 | 20 |
| 2 US gal | 2.00 | 40 |
At any other label dose, multiply the table dose by the label dose. A label of 2 mL per gallon in 1 gallon of dip water is 2.00 mL; a label of 1 mL per 2 gallons in 1 gallon is 0.50 mL.
FAQ
Does this tool pick the dip product or the dip time?
No. The product, the concentration and the dip time all come from your product label — this tool only does the arithmetic that scales the label dose to your container. It never recommends a product, a concentration or a duration.
Why 20 drops per millilitre?
It is the standard dropper approximation for water-like liquids. Real droppers vary, so for very small doses — under 1 mL — a 1 mL syringe is more accurate than counting drops.
What if my dose comes out under 1 mL?
Use a 1 mL syringe. Counting a handful of drops is too imprecise at that size, and a small error is a large percentage of a small dose.
Can I make the dip stronger to be safe?
No — never make a stronger dip to be safe. Overdosing can burn coral tissue or kill the coral. The label dose is the dose, scaled to your water volume.
What water do I dip in?
Display-tank water at tank temperature and salinity. Measure it with a jug into the dip container, time the dip per the label, and dispose of the used dip down the drain — never into the sump.
My coral looks sick — will a dip fix it?
A dip is a pest treatment scaled from a product label, not a diagnosis. If a coral shows disease signs — tissue loss, bleaching, or recession — this tool cannot tell you what is wrong or what to treat it with. See an aquatic veterinarian, and do not dose the display tank on a guess.
Sources
- Standard — NIST Handbook 44, Appendix C. The US gallon is 231 cubic inches and the cup is 1/16 of it, giving 1 US gal = 3.78541 L and 1 US cup = 0.2365882 L. Used for every volume conversion on the page. No URL on file — listed by name only.
- Hobby practice — the 20 drops = 1 mL dropper approximation. The standard approximation for water-like liquids, used to convert between millilitres and drops. It is a practical approximation, not a standard — droppers vary, which is why the tool tells you to use a syringe under 1 mL.
This tool's figures rest on one standard (NIST Handbook 44) and one practical approximation (20 drops per mL). The dose itself is arithmetic on your product label, not a published figure — the label is the authority, and no other source is used.