Enter your water depth and bracing and get the minimum glass thickness from published tables, with the thicker value wherever sources disagree. Depth drives the number, not volume: a tall narrow tank needs thicker glass than a long shallow one of the same gallons. This is an estimate only — verify with the tank manufacturer or a professional glazier before building. Everything runs in your browser; nothing is saved.
How it works
Water pressure at the bottom of a tank depends only on how deep the water is — hydrostatic pressure p = ρgh, where ρ is the density of fresh water (1,000 kg/m³) and g is 9.81 m/s². That is why the calculator asks for water depth, not volume or gallons, and why the thickness rises steeply with depth: roughly with depth to the power of 1.5, so 20% deeper water needs about 30% thicker glass.
The table. The calculator reads from a conservative table built from two published hobby tables, taking the thicker value wherever they disagree. The tables are for annealed float glass, side panels, at two bracing types:
Braced means the top edge is tied together by a frame or a centre brace. Rimless means no top brace — the top edge is free to bow, so the silicone seams carry more stress and the glass must be one tier thicker at the same depth.
The bottom panel. The table gives the minimum for the side panels. The bottom panel usually takes the same thickness or one tier thicker — ask your glazier, and make sure it sits on a flat, level stand top (a foam levelling mat under rimless tanks, a full frame under rimmed ones).
Length. Length matters less than depth once a pane is over twice as long as it is tall, but long spans still need bracing: over 48 in long, a centre brace (or euro-bracing) is part of the structure. The table assumes the top edge is braced; without it, use the rimless number instead.
The limit. Above 36 in of water depth no table value is given — bracing design, seam width and lifting become specialist work, so the calculator gives no thickness on purpose and tells you to consult a fabricator.
Worked example
A standard 55-gallon tank: 21 in of water, 48 in long, braced top — then the same tank built rimless.
Water depth 21 in, tank length 48 in, braced top. Then the same depth and length, rimless.
Look up the depth band in the table for the bracing type, taking the thicker value where the two published tables disagree. 21 in falls in the 19–24 in band.
Braced, 19–24 in: the two tables give 10 mm and 12 mm — the thicker value, 12 mm, is used. Rimless, 19–24 in: the tables give 12 mm and 15 mm — the thicker value, 15 mm, is used. 12 mm is 0.47 in; 15 mm is 0.59 in. The length (48 in) is not over 48 in, so no extra bracing note applies.
Minimum 12 mm glass braced (0.47 in), or 15 mm rimless (0.59 in) — the bottom panel the same or one tier thicker. Both are minimums to verify with the manufacturer or a glazier, not targets to beat.
A shallower case shows the other end of the table: 12 in of water, braced, needs only 6 mm (0.24 in); rimless at the same depth needs 8 mm (0.31 in). And a 40 in water depth gives no number at all — over 36 in is beyond the table, so consult a fabricator.
How to read your results
The big number is the minimum glass thickness in millimetres, with the inch equivalent beside it, plus the water depth and bracing it was worked out from. The stat grid repeats the four inputs that decide it: minimum thickness, water depth, bracing and tank length.
Read "minimum" literally: it is the thinnest glass the tables allow for the side panels, not a recommended thickness. Thicker is safer; thinner is not an option. If the result is "Consult a fabricator", the depth is beyond the published tables and no number is given on purpose.
The check rows are grouped into Needs action, Caution and OK. A "Needs action" row means the depth is beyond the table — get the design checked. Caution rows cover rimless builds and long spans. What to do next: verify the number with the tank manufacturer or a professional glazier before you buy glass, and ask them about the bottom panel — it usually takes the same thickness or one tier thicker than the sides.
Common mistakes
- Entering the glass height instead of the water height. Lower water means thinner glass — measure to the waterline, not the rim.
- Thinking volume decides thickness. A tall narrow tank needs thicker glass than a long shallow one of the same gallons, because pressure depends only on depth.
- Treating the minimum as a target to beat. The number is a minimum, not a recommendation — going thinner to save money is how tanks fail.
- Removing the frame or centre brace from a framed tank to make it look rimless. The brace is part of the structure; without it you need the rimless thickness, and the tank was not designed for it.
- Using rimless thickness for a braced tank, or the other way round. Rimless always needs thicker glass at the same depth — one tier up.
- Forgetting the bottom panel. The table is for the side panels; the bottom usually takes the same thickness or one tier thicker, and it needs a flat, level stand top.
- Using tempered glass for panes that need drilling. Tempered glass is stronger but shatters completely if damaged, and it cannot be drilled or cut after tempering. This calculator assumes ordinary annealed float glass.
- Building above 36 in of water from a chart. Past that depth, bracing design, seam width and lifting become specialist work — have a professional builder design and assemble it.
Minimum glass thickness by water depth
The conservative table this calculator reads from — annealed float glass, side panels. Where the two published tables disagree, the thicker value is used. Standard sheet sizes are 4, 5, 6, 8, 10, 12, 15, 19 and 25 mm, so a result of 12 mm is a standard sheet; a result between sizes rounds up to the next standard sheet.
| Water depth | Braced | Rimless |
|---|---|---|
| Up to 12 in | 6 mm | 8 mm |
| 13–18 in | 8 mm | 10 mm |
| 19–24 in | 12 mm | 15 mm |
| 25–30 in | 15 mm | 19 mm |
| 31–36 in | 19 mm | 19 mm |
| Over 36 in | Consult a fabricator | Consult a fabricator |
Rule of thumb from the same tables: a braced tank at 12 in of water needs about 5–6 mm, at 16 in about 8 mm, at 20 in 10–12 mm, and at 24 in 15 mm on long panes. Factory tanks are sometimes thinner than this table: their rims and centre braces add support and their designs are tested by the maker — never thin a factory tank's design; follow the maker's spec.
FAQ
How thick should aquarium glass be?
It depends on water depth and bracing, not on gallons. A braced tank at 12 in of water needs a minimum of 6 mm; at 21 in, 12 mm; at 30 in, 15 mm. Rimless needs one tier thicker at the same depth. Use the calculator for your depth, then verify with the manufacturer or a glazier.
Why does water height matter more than length?
Because hydrostatic pressure at the bottom depends only on how deep the water is. Length matters less once a pane is over twice as long as it is tall — the bending of a long low pane is captured by the table, but depth is what sets the pressure.
Why does rimless need thicker glass?
With no top frame or euro-brace, the top edge is free to bow and the silicone seams carry more stress. The calculator rounds rimless side and end panes up one standard size from the braced value at the same depth.
Why are factory tanks sometimes thinner than this table?
Their rims and centre braces add support, and their designs are tested by the maker. This conservative minimum is for a one-off build — never thin a factory tank's design; follow the maker's spec.
Glass or acrylic?
Acrylic is usually a little thinner at the same strength, but it is designed with a much larger safety factor (about 10 against 3.8 for glass) because it creeps under constant load. It is far lighter and does not shatter, but it scratches easily. This calculator covers annealed float glass only.
Can I use tempered glass?
Not for panes that need drilling, and not if you are unsure. Tempered glass is stronger but shatters completely if damaged, and it cannot be drilled or cut after tempering.
What if my water is deeper than 36 in?
Do not pick a thickness from a chart. Above about 36 in of water, or past 25 mm glass, bracing design, seam width and lifting become specialist work — have a professional builder design and assemble the tank.
Sources
- FishTankMath — aquarium glass thickness by volume, published hobby table (braced and rimless values by depth). fishtankmath.com/guides/aquarium-glass-thickness-by-volume
- AquariumCalculator.net — fish tank glass calculator, published hobby table (braced and rimless values by depth). aquariumcalculator.net/fish-tank-glass-calculator
- Young, W. C. and Budynas, R. G., Roark's Formulas for Stress and Strain, McGraw-Hill — bending coefficients for rectangular plates under hydrostatic and uniform pressure (Engineering). No source page URL is on file for this book; it is listed by name.
- Manufacturer technical data sheets — modulus of rupture of annealed soda-lime float glass about 19.2 N/mm²; tensile strength of cast acrylic (PMMA) sheet about 69–76 N/mm² (Manufacturer). No source page URL is on file; listed by name.