Aquarium Substrate Calculator

Units

Inside length — substrate fills the space inside the glass

1–3 inches suits most planted tanks

Densities are typical values — grain size and moisture shift them, so if the bag states its own weight and volume, that beats this estimate. Pounds = (length × width × depth in inches ÷ 1,728) × density in lb/ft³.

How much substrate do you need?

Enter the footprint and the target depth — the weight, the bed volume and the bag count appear here.

Why use this calculator?

  • Buy the right amount the first time — no second trip to the shop mid-scape.
  • Get the depth right for plants and roots, not just a rough guess.
  • See pounds, kilograms and bag counts together, so the shopping list is done.
  • Aquasoil is counted in litres, the way it is actually sold.

Don't know your tank's gallons? Measure it with the Tank Volume Calculator, or check the water itself with the Water Parameter Checker. · Back to Tank Size & Setup

Enter your tank's footprint and target depth and get the substrate weight in pounds and kilograms, plus how many bags to buy. Buy the right amount the first time — no second trip, and the right depth for plants and roots. Everything runs in your browser; nothing is saved.

How it works

Substrate depends on floor area, not on volume — a wide shallow tank needs more substrate than a tall narrow one of the same gallons. The calculator works out the bed volume first, then weighs it at a typical density for the type you pick.

Bed volume. Length × width × depth, all in inches, ÷ 1,728 = cubic feet (there are 1,728 cubic inches in a cubic foot). Use the INSIDE length and width — substrate fills the space inside the glass. For a bow-front, cylinder or hexagon tank, take the base area from that shape's volume calculator instead of length × width.

Weight. Cubic feet × density in lb/ft³. The densities are typical values, labelled typical because brands vary by grain size and moisture: gravel 100, sand 100, aquasoil 50 lb/ft³. Aquasoil varies the most — 50–60 lb/ft³ across published sources, with one source listing 80 — so aquasoil weights are the roughest of the three. If the bag states its own weight and volume, that beats this estimate.

Bags. Gravel and sand are counted in 20-lb bags, rounded up; aquasoil is sold by volume, so it is counted in 9-L bags, rounded up. One cubic foot is 28.3168 litres.

Sloped beds. A straight slope from front to back uses the same amount as a flat bed at the average of the two depths — run the calculator once at (front + back) ÷ 2.

Worked example

A 48 × 12 in footprint with a 2 in gravel bed — the classic 55-gallon shape at the usual community-tank depth.

Inputs

Length 48 in, width 12 in, depth 2 in, gravel at the typical 100 lb/ft³.

Formula

Volume = L × W × D ÷ 1,728. Weight = ft³ × density. Bags = weight ÷ 20, rounded up.

Calculation

48 × 12 × 2 = 1,152 in³; 1,152 ÷ 1,728 = 0.667 ft³. Weight = 0.667 × 100 = 66.7 lb. In kilograms: 66.7 × 0.45359237 = 30.2 kg. In litres: 0.667 × 28.3168 = 18.9 L. Bags: 66.7 ÷ 20 = 3.3, rounded up to 4.

Result

66.7 lb of gravel (30.2 kg, 18.9 L of bed) — 4 bags of 20 lb. Buy a fifth bag if you want the usual 10% extra for settling.

The same bed in aquasoil weighs half as much — 33.3 lb at the typical 50 lb/ft³ — but you buy it by volume: 18.9 L rounds up to three 9-L bags.

How to read your results

For gravel and sand, the big number is the weight in pounds, with kilograms, the bed volume in litres, and the 20-lb bag count beside it. For aquasoil, the big number is the litres, because aquasoil is sold by volume — the pounds are only a rough guide at the typical 50 lb/ft³ density.

The stat grid repeats the four numbers that matter: weight (or volume for aquasoil), bed volume in cubic feet, bags to buy, and the density used. The check rows say whether the depth suits the setup: under 1 in is a thin decorative layer, 1–3 in is the usual planted-tank depth, and over 3 in is a deep bed that can develop low-oxygen pockets if the substrate is fine.

What to do next: buy about 10% extra — substrate settles after filling, and hardscape and plants push it into mounds. Leftover dry gravel or sand keeps indefinitely if it stays dry. Rinse gravel and sand before adding; aquasoil goes in unrinsed.

Common mistakes

  • Using the "1 lb per gallon" rule. It is a rough guide at best: it gives a bed about 1–1.5 in deep in most standard tanks, but it breaks down for tall/narrow vs wide/shallow tanks because substrate depends on floor area, not volume. A 40-gallon breeder needs more gravel than a 55-gallon because its floor is larger.
  • Using the outside dimensions. Substrate fills the space inside the glass — measure the inside length and width, or the bed comes out too big.
  • Going too deep with fine substrate. Very deep fine beds can develop low-oxygen pockets — keep the bed at the depth the plants need, and no deeper.
  • Going too shallow for rooted plants. Under 1 in is a thin decorative layer; most rooted plants cannot anchor in it.
  • Buying aquasoil by weight. Aquasoil is sold by volume — buy by litres, and check the bag's own litre figure against this estimate.
  • Forgetting the slope. A bed deeper at the back than the front uses the average of the two depths — run the calculator once at (front + back) ÷ 2.
  • Counting a nutrient base layer and its cap as one bed. With a nutrient layer under a gravel or sand cap, run the calculator twice — once per layer.
  • Buying exactly the calculated amount. Substrate settles after filling, and you may want to deepen the back later — buy about 10% extra.

Substrate for standard tanks

Worked out with the same method as this calculator, for standard footprints. Gravel at 2 in deep in 20-lb bags; aquasoil at 2.5 in deep in 9-L bags. Sand matches gravel at the same density (both 100 lb/ft³ typical).

TankFootprintGravel, 2 inAquasoil, 2.5 in
10 gal20 × 10 in23.1 lb · 2 bags8.2 L · 1 bag
20 gal long30 × 12 in41.7 lb · 3 bags14.7 L · 2 bags
29 gal30 × 12 in41.7 lb · 3 bags14.7 L · 2 bags
40 gal breeder36 × 18 in75.0 lb · 4 bags26.5 L · 3 bags
55 gal48 × 13 in72.2 lb · 4 bags25.6 L · 3 bags
75 gal48 × 18 in100.0 lb · 5 bags35.4 L · 4 bags
125 gal72 × 18 in150.0 lb · 8 bags53.1 L · 6 bags

Depths by setup: about 2 in of gravel for community tanks (enough to anchor decor and hold bacteria without trapping much waste; deeper beds need regular vacuuming); planted tanks 2–3 in, often deeper at the back; reef tanks 1–2 in of aragonite; a deliberate deep sand bed 4–6 in for nitrate reduction — anything in between can trap waste; thin ½-in layers suit nano and shrimp tanks.

FAQ

How much gravel do I need?

It depends on the floor area and the depth, not the gallons. A 55-gallon tank (48 × 13 in) at 2 in deep needs 72.2 lb — four 20-lb bags. Use the calculator for your footprint and depth.

Does the "1 lb per gallon" rule work?

Only roughly: it gives a bed about 1–1.5 in deep in most standard tanks, but it breaks down for tall/narrow vs wide/shallow tanks because substrate depends on floor area, not volume. A 40-gallon breeder needs more gravel than a 55-gallon.

How deep should the substrate be?

About 2 in of gravel for community tanks; planted tanks 2–3 in, often deeper at the back; reef tanks 1–2 in of aragonite; a deliberate deep sand bed 4–6 in for nitrate reduction. Under 1 in is too shallow for most rooted plants.

How many bags of aquasoil do I need?

Buy by litres, not pounds: a 36 × 18 in tank at 2.5 in needs 26.5 L, which is three 9-L bags. Use the calculator for your footprint — the bag count is in the result.

How do I work out a sloped bed?

Use the average of the front and back depths: a slope from 1 in at the front to 3 in at the back uses the same amount as a flat 2 in bed. Run the calculator once at the average depth.

Should I buy extra?

Yes, about 10% extra. Substrate settles after filling, hardscape and plants push it into mounds, and you may want to deepen the back later. Leftover dry gravel or sand keeps indefinitely if it stays dry.

Sources

No URLs are listed for these sources because no source page URL is on file for them; they are listed by name.

  1. CaribSea FAQ — the substrate weight formula: pounds = (length × width × depth in inches ÷ 1,728) × density in lb/ft³ (Manufacturer).
  2. Standard engineering bulk-density tables — typical dry bulk densities of granular materials: gravel about 100 lb/ft³ (1.6 t/m³), sand about 95 lb/ft³ (1.5 t/m³) (Standard).
  3. Manufacturers' bag weights per litre — aragonite sand about 90 lb/ft³ and aquarium soils about 0.9 kg/L (55 lb/ft³) (Manufacturer).
  4. NIST Handbook 44, Appendix C — unit definitions for cubic inch, cubic foot, litre and pound (Standard).

Related tools