Reef Calcium Calculator

Raise magnesium first if it is low — and dose calcium apart from alkalinity

If magnesium is below about 1,250 ppm, raise it first; otherwise calcium and alkalinity precipitate and the correction does not hold. Dose calcium and alkalinity hours apart in different places. Anhydrous pellets get hot while dissolving — use a heat-safe container.

Volume units

Display plus sump, minus rock and substrate

From your calcium test kit, in ppm

Your own target — this tool never picks one for you

Dihydrate (flakes) is 27.3% calcium; anhydrous (pellets) is 36.1%

Default 50 ppm/day; the Red Sea manual caps daily calcium at 20 ppm/day

Calcium needed in grams = calcium gap in ppm × litres ÷ 1,000. Dihydrate in grams = calcium grams × 147.01 ÷ 40.078; anhydrous = calcium grams × 110.98 ÷ 40.078 (CRC Handbook molar masses). Worked example: a 100-gallon system (378.5 L) from 380 to 430 ppm needs 18.9 g of calcium = 69.4 g calcium chloride dihydrate in 1 day, or 52.4 g if anhydrous.

Your calcium dose

Enter your volume, current and target calcium — the calcium chloride dose in grams appears here, split across days so a big gap never lands in one dose.

Why use this calculator?

  • Get a one-off calcium correction in weighed grams — not a daily two-part dose, and not a guess from a scoop.
  • See the correction split across days, so a big gap never lands in one precipitating dose.
  • Compare dihydrate flakes and anhydrous pellets for the same correction, so swapping products means re-weighing, not guessing.
  • Know where the numbers come from — the stoichiometric formula is shown, with the CRC molar masses behind it.

Raise magnesium first with the Reef Magnesium Calculator, work out your daily two-part dose with the Reef Dosing Calculator, or check the rest of the water with the Water Parameter Checker. · Back to Saltwater & Reef

Work out how much calcium chloride raises your reef calcium by the amount you need — in weighed grams, split across days so a big gap never lands in one precipitating dose. Compare dihydrate flakes and anhydrous pellets for the same correction. Everything runs in your browser; nothing is saved.

How it works

Calcium is dosed as calcium chloride, and the tool works out the weight of the salt from the weight of the calcium inside it. The chemistry is stoichiometric — no product strength is guessed.

Calcium needed (g) = calcium gap (ppm) × litres ÷ 1,000. 1 ppm is 1 mg per litre, so the gap in ppm times the litres is the milligrams of calcium the tank is short, divided by 1,000 to give grams.

Dihydrate (g) = calcium (g) × 147.01 ÷ 40.078. Calcium chloride dihydrate, CaCl2·2H2O, weighs 147.01 g per mole and calcium weighs 40.078 g per mole — a factor of 3.668. Dihydrate flakes are 27.3% calcium by mass.

Anhydrous (g) = calcium (g) × 110.98 ÷ 40.078. Anhydrous calcium chloride, CaCl2, weighs 110.98 g per mole — a factor of 2.769. Anhydrous pellets are 36.1% calcium by mass, so the same correction weighs less as anhydrous.

Days = gap ÷ max rise per day, rounded up. The default cap is 50 ppm per day; the daily dose is the total grams divided by the number of days. The Red Sea Foundation manual caps daily calcium at 20 ppm/day — a gentler limit you can set in the max-rise box.

Why magnesium comes first. If magnesium is below about 1,250 ppm, calcium and alkalinity precipitate and the correction does not hold. Raise magnesium first, then calcium.

Where the targets sit. Natural seawater holds about 412 mg/kg of calcium at 35 ppt salinity; most reefs run 400–450 ppm. Above about 480 ppm there is no benefit, only more precipitation risk.

Worked example

A 100-gallon system (378.5 L) from 380 to 430 ppm with calcium chloride dihydrate, at a 50 ppm/day cap.

Inputs

378.5 litres, current 380 ppm, target 430 ppm, dihydrate, max rise 50 ppm/day.

Formula

Calcium (g) = gap × litres ÷ 1,000. Dihydrate = calcium × 147.01 ÷ 40.078. Days = gap ÷ max rise, rounded up.

Calculation

Gap = 430 − 380 = 50 ppm. Calcium = 50 × 378.54 ÷ 1,000 = 18.93 g. Dihydrate = 18.93 × 147.01 ÷ 40.078 = 69.43 g. Anhydrous instead = 18.93 × 110.98 ÷ 40.078 = 52.41 g. Days = 50 ÷ 50 = 1 day.

Result

69.4 g calcium chloride dihydrate in 1 day (or 52.4 g if anhydrous). Dissolve, pour slowly into the sump, retest tomorrow.

A second case from the same test checks: the same 100-gallon system from 350 to 450 ppm needs 138.9 g dihydrate, split 69.4 g/day over 2 days at the same 50 ppm/day cap. And at the gentler Red Sea cap of 20 ppm/day, the worked example stretches to 3 days at 23.1 g per day.

How to read your results

The verdict word is the headline: the total grams of the calcium chloride you chose. The stat grid shows the three numbers behind it — the total dose, the dose per day, and the daily rise in ppm with the cap you set.

Read the rows under the verdict for the next step. "Needs action" means do it now — usually the split itself, or dosing calcium apart from alkalinity. "Caution" means respect the limit: a big one-off calcium dose precipitates with alkalinity and drops both readings. "OK" means that check passed — the dose fits inside one safe daily rise, or the handling note is one to follow rather than a warning.

If the verdict says "No dose needed", your calcium is already at or above target. Do not dose to push it higher — calcium only falls through coral use and water changes, and an overshoot has to be waited out or diluted.

Common mistakes

  • Swapping dihydrate and anhydrous without re-weighing. The same calcium weighs 69.4 g as dihydrate flakes and 52.4 g as anhydrous pellets for the worked example — the same scoop of each is a different dose.
  • Dosing calcium and alkalinity together. They precipitate as calcium carbonate ("snow") and both readings drop. Dose them hours apart, in different places.
  • Correcting calcium while magnesium is low. Below about 1,250 ppm magnesium, calcium and alkalinity will not hold — raise magnesium first.
  • Landing a big gap in one dose. A large one-off calcium dose precipitates with alkalinity; split it across days at your daily cap and retest before each dose.
  • Dissolving anhydrous pellets in a thin container. They get hot while dissolving — use a heat-safe container and let the solution cool before adding it.
  • Using the display volume instead of the net volume. Rock and substrate displace water, so the label gallons overstate the water — measure the system volume with the Tank Volume Calculator first.
  • Chasing a number above about 480 ppm. There is no benefit past that point, only more precipitation risk — steady inside 400–450 ppm matters more than a high reading.

Grams to raise calcium by 10 ppm

Calcium chloride for a 10 ppm rise at each tank size, recomputed with the formula above. Read your size across, then multiply by the gap in tens of ppm you need to close.

System volumeDihydrateAnhydrous
25 gal (94.6 L)3.5 g2.6 g
50 gal (189.3 L)6.9 g5.2 g
75 gal (283.9 L)10.4 g7.9 g
100 gal (378.5 L)13.9 g10.5 g
150 gal (567.8 L)20.8 g15.7 g
200 gal (757.1 L)27.8 g21.0 g

Check it against the worked example: 100 gallons needs 13.9 g per 10 ppm, so a 50 ppm rise is 5 × 13.9 = 69.4 g — the same 69.4 g the tool gives.

FAQ

Why does the tool default to 50 ppm a day when Red Sea says 20?

The 50 ppm/day default is the research default this tool ships with; the Red Sea Foundation manual caps daily calcium at 20 ppm/day, which is much gentler. The cap is editable in the form — set the max-rise box to 20 for the slower correction our Reef Dosing Calculator uses, and never raise calcium faster than your livestock tolerates.

Dihydrate or anhydrous — which should I use?

Either closes the same gap; the grams differ because the water of crystallisation differs (69.4 g dihydrate against 52.4 g anhydrous for the worked example). Dihydrate flakes dissolve without heating up; anhydrous pellets get hot while dissolving, so they need a heat-safe container and cooling time. Never swap one for the other without re-weighing.

Why raise magnesium first?

Magnesium holds calcium and alkalinity in solution. Below about 1,250 ppm magnesium, the two precipitate as calcium carbonate and the correction does not hold — you add calcium, it snows out, and the reading barely moves. Fix magnesium first, then calcium.

What causes the white "snow" when I dose?

Calcium and alkalinity dosed together — or a big calcium dose landing in high-alkalinity water — precipitate as calcium carbonate. Dose them hours apart in different places, add each dose slowly to high flow, and split big corrections across days.

What if my calcium is already above target?

Dose nothing. The tool says "No dose needed" and gives no grams. Calcium only falls through coral use and water changes, so an overshoot has to be waited out or diluted — do not chase it down with another chemical.

How high is too high?

Most reefs run 400–450 ppm, against about 412 mg/kg in natural seawater at 35 ppt. Above about 480 ppm there is no benefit, only more precipitation risk. Steady inside the range matters more than any single high number.

Sources

  1. Textbook — Haynes (ed.), CRC Handbook of Chemistry and Physics. Used for the molar masses: Ca 40.078; CaCl2·2H2O 147.01; CaCl2 110.98 — the 27.3% and 36.1% calcium contents follow from them.
  2. Hobby practice — Holmes-Farley, R., Reefkeeping Magazine / Advanced Aquarist. Used for the method and the practical limits (dose calcium apart from alkalinity, magnesium first when low, anhydrous pellets get hot).
  3. Textbook — Millero, F. J., Chemical Oceanography, CRC Press. Used for natural seawater calcium, about 412 mg/kg at 35 ppt.
  4. Manufacturer — Red Sea Foundation manual. Caps daily calcium at 20 ppm/day. Cited as the gentler limit the tool offers against its 50 ppm/day default; the disagreement is stated on the page, not hidden.

No links are given here because no source web address was on file for these references — they are named so you can look them up.

Related tools