Root Tab Calculator

Grid: tabs along each side = ⌈side × √planted share ÷ spacing⌉; total = length tabs × width tabs. Tabs per year = tabs × 12 ÷ replacement months. By plants: 2 tabs per large root feeder + 1 per medium. Push each tab deep to the bottom of the substrate — shallow tabs leak into the water and feed algae instead of the roots. Count heavy root feeders only: stem plants and epiphytes such as anubias take little from the substrate. For freshwater planted tanks.

How many root tabs?

Enter your tank footprint, planted share and spacing — the tab count, grid and yearly total appear here.

Why use this calculator?

  • Buy the right number of tabs for your floor, in a grid that covers the edges — instead of guessing a packet size.
  • See the yearly cost up front, so a 2-month replacement cycle does not surprise you at the shop.
  • Cross-check the grid against a per-plant count, so heavy feeders get the extra tabs they need.
  • Know when aquasoil is still young enough that tabs can wait, instead of dosing on top of fresh soil.
  • Adjust spacing and watch the count change, so the trade-off between coverage and cost is visible.

Feeding the water column too? The Fertilizer Dosing Calculator works out liquid doses. Planning the substrate itself? Try the Substrate Calculator. · Back to Planted Tank

Work out how many root tabs your tank floor needs, in a grid that covers the edges, and what that costs per year — so you buy the right number the first time. Everything runs in your browser; nothing is saved.

How it works

The calculator lays tabs out in a grid over the planted part of your floor. Tabs along each side = ⌈side × √planted share ÷ spacing⌉, and the total is the length tabs × the width tabs. The square root shrinks each side by the planted fraction, so the planted area — not the whole floor — is covered, and rounding up on each side means the edges are always covered.

Tabs per year. Tabs × 12 ÷ months between replacements. Replace every 2–3 months — check your brand. A 2-month cycle on 24 tabs is 144 tabs a year, so the yearly number is the one that decides the packet size.

By plants. The second count is 2 tabs per large root feeder + 1 per medium. It cross-checks the grid: the grid covers the planted area, the plant count counts only the heavy feeders. If the two disagree, trust the grid for the order and use the plant count to make sure the heavy feeders get their extra tabs where they sit.

Spacing. 4–8 in follows common manufacturer guidance. Tighter spacing means more tabs: halving the spacing roughly quadruples the count.

Aquasoil. Aquasoil under about 6 months old still holds nutrients, so the calculator advises no tabs yet in that case — the count is still shown, for when the soil runs down.

Worked example

A 48 × 13 in floor (55 gal), fully planted, 6 in spacing, inert substrate, replaced every 2 months.

Inputs

Length 48 in, width 13 in, planted share 100%, spacing 6 in, inert substrate, replace every 2 months.

Formula

Tabs along each side = ⌈side × √share ÷ spacing⌉. Total = length tabs × width tabs. Per year = tabs × 12 ÷ months.

Calculation

√100% = 1, so ⌈48 ÷ 6⌉ = 8 along the length and ⌈13 ÷ 6⌉ = 3 along the width. 8 × 3 = 24 tabs. 24 × 12 ÷ 2 = 144 a year.

Result

24 tabs in an 8 × 3 grid, 144 a year.

Two more checks on the same floor. By plants: 4 large + 6 medium root feeders → 2 × 4 + 6 = 14 tabs — the grid's 24 still decides the order, and the 14 tells you where the heavy feeders sit. Partly planted: the same floor at 25% planted share → √25% = 0.5, so ⌈48 × 0.5 ÷ 6⌉ × ⌈13 × 0.5 ÷ 6⌉ = 4 × 2 = 8 tabs.

How to read your results

The verdict word is the total tab count. Under it, the grid line names the layout, the floor size, the planted share and the spacing. The stat grid shows the three numbers that decide the order: total tabs, tabs per year, and the by-plant count.

If the by-plant count is blank, enter your large and medium root-feeder counts to cross-check the grid. If it is much lower than the grid total, that is normal — the grid covers the whole planted floor, while the plant count only counts heavy feeders.

If your substrate is aquasoil under 6 months old, the result carries a Caution: hold off on the tabs for now and use this count when the soil starts to run down. Yellowing older leaves on swords is the usual sign the tabs have run out.

What to do next: buy the grid number, push each tab deep to the bottom of the substrate, and set the replacement on a 2–3 month cycle.

Common mistakes

  • Counting stem plants and epiphytes such as anubias as root feeders — they take little from the substrate.
  • Pushing tabs in shallow. Shallow tabs leak into the water column and feed algae instead of the roots.
  • Dosing tabs on top of fresh aquasoil that still holds nutrients.
  • Using the whole floor when only part of it is planted — set the planted share, or the count comes out high.
  • Rounding down instead of up, which leaves bare edges.
  • Forgetting the replacement cycle. Tabs run out after 2–3 months, and yellowing older leaves on swords is the usual sign.
  • Buying by packet size instead of by the grid — a packet that almost covers the floor still leaves a corner unfed.

Tabs for a fully planted floor

Grid counts at 100% planted, by spacing. At any other share, multiply each side by √share first, then round up.

Floor8 in6 in4 in
30 × 12 in (20 gal long / 29 gal)81024
36 × 18 in (40 gal breeder)151845
48 × 13 in (55 gal)122448
48 × 18 in (75 gal)182460

Read across a row to see what tighter spacing costs: on a 48 × 13 in floor, 8 in spacing needs 12 tabs, 6 in needs 24, and 4 in needs 48.

FAQ

How often do I replace root tabs?

Every 2–3 months — check your brand. The tabs per year figure is the count that decides how many packets to buy.

Do I need root tabs with fresh aquasoil?

No. Aquasoil under about 6 months old still holds nutrients, so tabs can wait. Use the calculator's count when the soil starts to run down.

How deep do I push each tab?

Deep to the bottom of the substrate. Shallow tabs leak into the water column and feed algae instead of the roots.

Which plants count as root feeders?

Heavy root feeders: swords, crypts, crinums, aponogetons, tiger lotus and vallisneria. Large ones get 2 tabs, medium ones 1.

Do stem plants need root tabs?

They take little from the substrate, so do not count them — the same goes for epiphytes such as anubias.

My grid says 24 tabs but my plant count says 14 — which is right?

Both. The grid covers the whole planted floor; the plant count only counts heavy feeders. Buy the grid number, and put the extra tabs near the heavy feeders.

The older leaves on my swords are yellowing — are the tabs spent?

That is the usual sign the tabs have run out. Replace them on the 2–3 month cycle rather than waiting for more leaves to yellow.

Sources

No URLs are on file for these sources; they are listed by name.

  1. Kasselmann, C., Aquarium Plants, Krieger Publishing, 2003 — root feeding of Echinodorus, Cryptocoryne and other rosette plants (Textbook).
  2. Root tab manufacturer guidance — spacing of 4–8 in between tabs (Manufacturer).
  3. TheCycledTank method — grid layout: tabs along each side = ⌈side × √share ÷ spacing⌉; total = length tabs × width tabs; per year = tabs × 12 ÷ months (Our method).

Related tools