Enter your tank size and target ammonia, and get the exact dose in mL or drops — plus what to test next. Everything runs in your browser; nothing is saved.
How it works
A fishless cycle feeds ammonia to grow the bacteria that will later keep fish safe — no fish are in the tank while it happens, because ammonia at these levels harms fish. The tool works out how much ammonia to add to reach your target, after subtracting the ammonia already in the water.
The dose, in milligrams. 1 ppm means 1 mg per litre, so dose (mg) = target ppm × litres. A 20-gallon tank holds 75.71 litres, so reaching 2 ppm there takes 2 × 75.71 = 151.42 mg of ammonia.
Liquid solution, in millilitres. mL = dose (mg) ÷ (strength % × 10), because a P% solution holds P × 10 mg per mL — a 10% solution holds 100 mg/mL. So 151.42 mg ÷ 100 = 1.51 mL of a 10% solution.
Dr. Tim's drops. The product's own instructions say 4 drops per gallon raises ammonia to about 2 ppm — that is 2 drops per gallon per ppm. So drops = gallons × ppm needed × 2.
What counts as done. Dose to 2–4 ppm — the standard dose is 2 ppm, with 4 ppm as the heavy option. The cycle is complete when ammonia and nitrite both read 0 within 24 hours of a 2 ppm dose. That usually takes 4–8 weeks, test-confirmed.
Worked example
A 20-gallon tank, target 2 ppm, current reading 0, 10% liquid ammonia solution — and the same case in drops.
20 gallons, target 2 ppm, current 0 ppm, 10% liquid solution. The drops version uses the same tank and target.
Litres = gallons × 3.78541. Dose (mg) = ppm needed × litres. mL = dose ÷ (strength % × 10). Drops = gallons × ppm needed × 2.
Litres = 20 × 3.78541 = 75.71 L. Needed = 2 − 0 = 2 ppm. Dose = 2 × 75.71 = 151.42 mg. Liquid: 151.42 ÷ (10 × 10) = 151.42 ÷ 100 = 1.51 mL. Drops: 20 × 2 × 2 = 80 drops.
1.51 mL of 10% solution, or 80 drops of Dr. Tim's — then test daily and top up to hold 2 ppm while nitrite is still showing.
One more check, with ammonia already in the water: the same 20-gallon tank, target 4 ppm, current reading 0.5 ppm, 10% solution. Needed = 4 − 0.5 = 3.5 ppm. Dose = 3.5 × 75.71 = 265.0 mg, so 265.0 ÷ 100 = 2.65 mL. If the current reading is already at or above the target, the tool says no dose is needed — test again tomorrow before dosing anything.
How to read your results
The big number is the dose — in millilitres for a liquid solution, in drops for Dr. Tim's, or "No dose needed" when your water already reads at or above target. The stat grid shows the same dose, the tank volume in litres, and the ppm you still need to add (target minus current).
Under the dose, the rows say what happens next: dose to 2–4 ppm and test daily, topping up to hold the target while nitrite is still showing; the cycle is done when a 2 ppm dose reads 0 ammonia and 0 nitrite within 24 hours; and only dose a fishless tank, with pure ammonia only.
Measure liquids with a syringe — kitchen spoons are not accurate at this scale. A 1.51 mL dose is about a third of a teaspoon, and a small error is a large share of it.
Common mistakes
- Dosing with fish in the tank. Ammonia at 2–4 ppm harms fish — this tool is fishless-cycle only.
- Using ammonia with surfactants, fragrances or dyes. Only pure ammonia is safe to use; if it foams when shaken, do not use it.
- Dosing to the target once and forgetting it. The bacteria eat ammonia as they grow, so the level falls — test daily and top up to hold the target while nitrite is still showing.
- Guessing the solution strength. The dose in mL depends on the % on the bottle — a 5% solution needs double the mL of a 10% solution for the same ppm.
- Measuring millilitres with a kitchen spoon. Use a syringe; at 1.51 mL, a spoon's error is most of the dose.
- Calling the cycle done on one clean reading. Only the confirmation test counts: dose 2 ppm, and 24 hours later ammonia and nitrite both read 0.
- Thinking bottled bacteria skip the wait. A full cycle usually takes 4–8 weeks — there is no safe shortcut.
Dose table — 10% liquid solution, current reading 0
Millilitres of 10% ammonia solution to reach the target, for common tank sizes. All figures from the same arithmetic as the worked example: litres = gallons × 3.78541, dose = ppm × litres ÷ 100.
| Tank size | To 2 ppm | To 4 ppm | Drops to 2 ppm |
|---|---|---|---|
| 5 gal | 0.38 mL | 0.76 mL | 20 drops |
| 10 gal | 0.76 mL | 1.51 mL | 40 drops |
| 20 gal | 1.51 mL | 3.03 mL | 80 drops |
| 40 gal | 3.03 mL | 6.06 mL | 160 drops |
| 75 gal | 5.68 mL | 11.36 mL | 300 drops |
With ammonia already in the water, subtract the current reading from the target first — the table assumes a current reading of 0. At 5 gallons the 2 ppm dose is 0.38 mL: measure it with a 1 mL syringe, not a spoon.
FAQ
How much ammonia do I dose for a fishless cycle?
2 ppm is the standard dose, with 4 ppm as the heavy option. This tool works out the exact amount for your tank size and target — 1.51 mL of 10% solution, or 80 drops, for a 20-gallon tank to 2 ppm — after subtracting the ammonia already in the water.
How do I know when the cycle is done?
Dose 2 ppm ammonia; 24 hours later, ammonia and nitrite must both read 0. That is the confirmation test, and it is the only proof that counts — one clean reading without dosing is not enough. A full cycle usually takes 4–8 weeks.
Can I dose ammonia with fish in the tank?
No. Ammonia at 2–4 ppm harms fish. This tool is for a fishless cycle only — if fish are already in the tank, do not dose ammonia at all, and if ammonia is showing, do a water change and check the filter instead.
What kind of ammonia is safe to use?
Only pure ammonia with no surfactants, fragrances or dyes. If it foams when shaken, do not use it. Check the bottle's strength (%) too — the dose in mL depends on it, and the tool needs the right number.
Why does the tool ask for my current ammonia reading?
Because the dose is the gap between target and current. If your water already reads 0.5 ppm and your target is 4 ppm, you only need 3.5 ppm more — 2.65 mL in a 20-gallon tank, not the full 4 ppm dose. If you are already at or above target, no dose is needed.
Do I keep dosing after nitrite appears?
Yes — top up to hold the target while nitrite is still showing. The bacteria you are growing eat ammonia first, then nitrite, so the ammonia level falls as the colony grows. Keep testing daily until the confirmation test passes.
Does this tool treat sick fish?
No. It is math only — it scales a dose for a fishless cycle. It never diagnoses fish or recommends a treatment; sick fish need an aquatic vet.
Sources
- Our recommendation — TheCycledTank species database (data/species-db.json, care_baselines). Dose 2–4 ppm ammonia; complete when ammonia and nitrite both read 0 within 24 hours of a 2 ppm dose; a full fishless cycle takes 4–8 weeks, test-confirmed.
- Manufacturer — Dr. Tim's Aquatics, Ammonium Chloride product instructions. 4 drops per gallon raises ammonia to about 2 ppm — the basis for the drops calculation (2 drops per gallon per ppm).
- Our guide — TheCycledTank fishless cycle guide. The full method this tool's dose fits into, linked from the tool page.
This tool's figures come from the site's own baselines and the product's own instructions; the dose itself is arithmetic from the definition of ppm (1 ppm = 1 mg per litre) and the gallon-to-litre conversion (1 US gal = 3.78541 L). No standard or textbook source was found for a fishless-cycle dose — treat the 2–4 ppm target as the site's own tested practice, and verify against your test kit.