Enter your total ammonia reading, pH and temperature and find out how much of it is the toxic free ammonia — and whether it is an emergency. Everything runs in your browser; nothing is saved.
How it works
A test kit measures total ammonia — free ammonia (NH3) plus ammonium (NH4+) together. Only the free NH3 crosses gills readily, so only that part is acutely toxic. Its share is set by pH and temperature, through the equation of Emerson, Russo, Lund & Thurston (1975), the reference equation in fisheries science and in the US EPA's ammonia water-quality criteria.
pKa = 0.09018 + 2729.92 ÷ T, where T is the water temperature in kelvin (°C + 273.15). At 25 °C (77 °F), pKa is 9.25.
Free share = 1 ÷ (1 + 10^(pKa − pH)). When pH is far below pKa, almost all the ammonia is harmless ammonium; each whole pH unit closer to pKa multiplies the free share roughly tenfold.
Toxic NH3 (ppm) = total ammonia (ppm) × free share. That is the number the verdict bands judge.
The verdict bands. Under 0.02 ppm free NH3 is generally safe; 0.02–0.05 ppm stresses fish over time; 0.05–0.20 ppm is dangerous; 0.20 ppm and over is in the range that kills. These are general guides for common freshwater fish — fry, shrimp and sensitive species can be harmed at lower levels.
Freshwater only. This tool does not apply a salinity correction. In seawater the salt raises pKa by about 0.1, so the true free fraction is roughly a fifth lower than the figure shown — the tool errs on the cautious side in a reef tank. Reef tanks run at pH 8.0–8.4, so any ammonia in them is a real risk either way.
Worked example
A liquid kit reads 1.0 ppm total ammonia; pH 7.4, 77 °F (25 °C), freshwater.
Total ammonia 1.0 ppm, pH 7.4, 25 °C (77 °F), freshwater.
pKa = 0.09018 + 2729.92 ÷ T, T in kelvin. Free share = 1 ÷ (1 + 10^(pKa − pH)). Toxic NH3 = total × free share.
T = 25 + 273.15 = 298.15 K. pKa = 0.09018 + 2729.92 ÷ 298.15 = 9.25. Free share = 1 ÷ (1 + 10^(9.25 − 7.4)) = 1 ÷ (1 + 70.8) = 1.40%. Toxic NH3 = 1.0 × 0.0140 = 0.014 ppm.
0.014 ppm free NH3 — safe (under 0.02 ppm). Keep testing, and find the source if the total stays above zero.
The same reading turns dangerous if the pH climbs. At pH 8.0 the free share is 5.37%, so the same 1.0 ppm total gives 0.054 ppm — dangerous. At pH 7.0 the share is only 0.56%, giving 0.006 ppm. And at pH 8.2 and 26 °C, 1.0 ppm total is 8.80% free, or 0.088 ppm — dangerous. That is why the pH next to the ammonia reading matters more than the ammonia number alone.
How to read your results
The verdict word is the headline, and the stat grid shows the three numbers behind it: the toxic NH3 in ppm, the free share as a percentage of your total reading, and the pKa at your temperature.
Under 0.02 ppm: generally safe — keep the routine going and keep testing. 0.02–0.05 ppm: stressful over time, with gill damage on repeated exposure — do a partial water change, find the ammonia source, and retest. 0.05–0.20 ppm: actively harmful — large water change now, stop feeding, and check the filter. 0.20 ppm and over: in the range that kills — emergency water change immediately and use a detoxifier per its label; do not wait to see if the fish recover on their own.
Read the rows under the verdict for the next step. "Needs action" means do it now. "Caution" means fix it soon. "OK" means that check passed — but a safe verdict today is not a safe verdict tomorrow: the same total reading turns dangerous if pH or temperature climbs.
If fish are gasping at the surface, treat it as an emergency whatever the number says, and check nitrite too — nitrite is separately toxic and this tool does not model it.
Common mistakes
- Reading the total ammonia number as the toxic number — at pH 7.4 only about 1.4% of it is toxic, at pH 8.0 about 5.4%.
- Raising pH while ammonia is present. A low pH is the only thing keeping the ammonia mostly harmless — fix the ammonia first, then the pH.
- Testing once and relaxing. Ammonia appears after overfeeding, a dead fish, overstocking, or a filter cleaned too hard — retest daily until it reads zero.
- Assuming a safe reading in acidic water means the tank is fine. The ammonia is still there, and it turns toxic quickly if pH rises — often after a water change with harder tap water.
- Using this freshwater number in a reef tank without remembering it reads about a fifth high there — and without remembering that reef pH makes any ammonia a real risk anyway.
- Forgetting nitrite. Ammonia is only half the nitrogen story; nitrite is just as toxic and needs its own test.
Free-ammonia share by pH (freshwater, 77 °F / 25 °C)
The share of a total ammonia reading that is toxic free NH3, and the total reading that would give 0.02 ppm free NH3 — the safe limit — at each pH. All figures recomputed with the Emerson equation above.
| pH | Free share | Total reading for 0.02 ppm free |
|---|---|---|
| 6.5 | 0.18% | 11.17 ppm |
| 7.0 | 0.56% | 3.55 ppm |
| 7.5 | 1.76% | 1.14 ppm |
| 8.0 | 5.37% | 0.37 ppm |
| 8.5 | 15.21% | 0.13 ppm |
| 9.0 | 36.19% | 0.06 ppm |
Read it as a warning about pH, not as permission: at pH 6.5 a tank can carry 11 ppm total ammonia before the free part reaches 0.02 ppm, but at pH 9.0 it takes only 0.06 ppm. The total reading that is safe falls fast as pH rises.
FAQ
How much ammonia is toxic to fish?
It is the free NH3 that counts, not the total: under 0.02 ppm free NH3 is generally safe, 0.02–0.05 ppm stresses fish over time, 0.05–0.20 ppm does harm within days, and over 0.20 ppm can kill quickly. Fry, shrimp and sensitive species can be harmed at lower levels.
Why does pH matter so much?
Each whole pH unit closer to pKa (about 9.25 at 77 °F) multiplies the free share roughly tenfold. A 1 ppm total reading is 0.006 ppm toxic at pH 7.0 and 0.054 ppm toxic at pH 8.0 — the same water, nine times the danger.
Is ammonia safer in acidic water?
Only for now. Below pH 7 almost all of it is harmless ammonium, but it turns toxic quickly if pH rises — often after a water change with harder tap water. Treat any ammonia in a low-pH tank as a problem to fix, not a safe level, and never raise pH until the ammonia is gone.
Does my test kit measure free or total ammonia?
Most liquid kits (API, Salifert) and strips measure total ammonia (NH3 + NH4+) reported as NH3 — that is what this tool expects. Some European kits report as NH4+, and lab reports as NH3-N; the Seachem Ammonia Alert badge reads free NH3 directly. If your kit reports a different form, convert it to total as NH3 first.
Is ammonia more toxic in saltwater?
Slightly less toxic at the same pH and temperature — salt shifts the balance toward ammonium, so at pH 8.2 and 26 °C the free share is about 8.0% in 35 ppt seawater against 8.8% in freshwater. But reef tanks run at pH 8.0–8.4, so any ammonia in them is still a real risk. This tool shows the freshwater figure, which reads about a fifth high in saltwater.
What do I do if the result is harmful?
Change 30–50% of the water with dechlorinated, temperature-matched water, stop feeding for a day, and dose an ammonia-binding conditioner per its label — it holds ammonia in a less-toxic form for about a day, buying time while the filter catches up. Then find the cause (overfeeding, a dead fish, overstocking, a filter cleaned too hard) and retest daily until ammonia reads zero. If fish look sick, see an aquatic vet — this tool calculates a number, it does not diagnose fish.
Sources
- Peer-reviewed — Emerson, Russo, Lund & Thurston (1975). Aqueous ammonia equilibrium calculations: effect of pH and temperature. Journal of the Fisheries Research Board of Canada 32: 2379–2383. Used for the pKa equation and the free-share formula.
- Government — US EPA, Aquatic Life Ambient Water Quality Criteria for Ammonia — Freshwater (2013). Used for how pH and temperature set ammonia toxicity, and for the 0.02 ppm long-term limit the verdict bands are built around.
- Government — Florida Cooperative Extension (UF/IFAS), fact sheets on ammonia in aquatic systems. Used for the aquaculture practice figure of about 0.02 mg/L un-ionized ammonia as the long-term limit for fish.
- Peer-reviewed — Khoo, Culberson & Bates (1977). Thermodynamics of the dissociation of ammonium ion in seawater from 5 to 40 °C. Journal of Solution Chemistry 6: 281–290. Used for the salinity correction this tool does not apply — the reason the freshwater figure reads about a fifth high in seawater.
- Peer-reviewed — Whitfield (1974); Spotte & Adams (1983). Cited in the tool's own reference note for the seawater pKa shift of about 0.1. The saltwater figures in the FAQ come from that note, not from a fresh calculation.