Aquarium Electricity Cost Calculator

Hours/day: — a heater cycles on a thermostat, it does not run 24 h
Hours/day:
Hours/day:
Hours/day:
From your electricity bill — 0.17 is a typical US starting point

Month is a 30-day month, year is 365 days. Watts come from the label on each device; hours are what you run them. Leave a device blank (or 0) if you do not have one.

What does it cost to run?

Enter at least one device — watts and hours per day — plus your electricity rate, and the monthly and yearly cost appears here, with which device eats the budget.

Why use this calculator?

  • See the real running cost before buying gear — a second tank is a monthly bill, not just a purchase.
  • Spot the hungry device — the per-device table shows which one eats the budget.
  • Compare LED vs old lights — swap the wattage and see the yearly difference in dollars.

Size the heater first with the Heater & Filter Sizer, then price the whole setup with the Setup Cost Estimator. · Back to Tank Size & Setup

Enter each device's watts and hours per day plus your electricity rate, and see the real monthly and yearly running cost — and which device eats the budget. A second tank is a monthly bill, not just a purchase. Everything runs in your browser; nothing is saved.

How it works

The maths is plain arithmetic, with nothing hidden inside it. For each device, the energy per day is watts × hours per day ÷ 1,000, which gives kilowatt-hours (kWh) per day. Add the devices together for the tank's total kWh per day.

Month and year. A month here is a 30-day month: monthly kWh = daily kWh × 30. A year is 365 days: yearly kWh = daily kWh × 365. Cost is kWh × your rate in dollars per kWh — the rate from your own bill, not a national average.

The rate. The form starts at $0.17/kWh, a typical US residential starting point. The US average residential price was 17.3 cents/kWh in 2025 and is projected at 18.2 cents for 2026 (EIA, Short-Term Energy Outlook, October 2026) — but your rate is what matters, and it varies a lot by state and by plan. Read it off your bill: the total bill divided by the kWh used is a better rate to enter than the headline energy charge alone, because delivery charges are part of what you pay.

Heater hours are a guess. A heater does not run 24 hours a day — it cycles on a thermostat. The form starts the heater at 12 hours a day, the filter and pump at 24, and the light at 8. Those are typical starting points to adjust, not measurements of your tank. If your room is cold the heater runs more and the real cost is higher; a plug-in power meter gives the true number.

Watts come from the label. Read the watts off the label on each device or its power brick. Leave a device blank — or 0 — if you do not have one.

Worked example

A 20-gallon community tank: 100 W heater, 10 W filter, 30 W light, 15 W pump, at $0.17/kWh.

Inputs

Heater 100 W × 12 h, filter 10 W × 24 h, light 30 W × 8 h, pump 15 W × 24 h. Rate $0.17/kWh.

Formula

kWh/day = watts × hours ÷ 1,000, per device, then added. Cost/month = kWh/day × 30 × rate. Cost/year = kWh/day × 365 × rate.

Calculation

Heater: 100 × 12 ÷ 1,000 = 1.20 kWh/day. Filter: 10 × 24 ÷ 1,000 = 0.24. Light: 30 × 8 ÷ 1,000 = 0.24. Pump: 15 × 24 ÷ 1,000 = 0.36. Total: 1.20 + 0.24 + 0.24 + 0.36 = 2.04 kWh/day. Month: 2.04 × 30 = 61.2 kWh. Cost: 61.2 × $0.17 = $10.40/month. Year: 2.04 × 365 × $0.17 = $126.58.

Result

$10.40/month, about $126.58/year. The heater is 59% of it ($6.12/month) — that is where any saving has to come from.

Check the heater share: $6.12 ÷ $10.40 = 59%. The filter is $1.22/month, the light $1.22/month, the pump $1.84/month. A second identical tank would double the bill to about $20.81/month.

How to read your results

The big number is the monthly cost, with the daily kWh and your rate under it. The stat grid repeats the monthly cost, the yearly cost, and the daily energy — so you can see the same answer at three scales.

The per-device table is where the decisions live. Each row shows the device, its kWh per day, its cost per month, and its share of the total. The hungriest device is the only one worth optimising: shaving watts off a filter that costs $1.22/month saves pennies, while cutting the heater's hours moves real money.

The rows under the table say the same in words. If the heater is the hungriest device, the fix is to cut its hours — a tighter lid, a warmer room, the tank away from a draughty window — not to buy a smaller heater, which then runs longer to do the same work. If the light is the hungriest, an LED at the same brightness is the saving: swap the wattage in the form and watch the yearly figure fall.

Common mistakes

  • Counting the heater at 24 hours a day. A heater cycles on a thermostat — 12 hours is the typical starting point, and the real number depends on the room. At 24 hours the worked example's heater alone would be $12.24/month instead of $6.12.
  • Using the headline energy charge instead of the real rate. Delivery charges are part of what you pay — total bill divided by kWh used is the rate to enter.
  • Comparing watts instead of kilowatt-hours. A 100 W heater running 12 hours (1.20 kWh/day) costs more than a 30 W light running 8 hours (0.24 kWh/day) — watts alone say nothing without hours.
  • Forgetting the filter and pump run all day. They are small watts, but 24 hours a day, every day — in the worked example they are $3.06/month together.
  • Assuming a smaller heater saves money. A heater that is too small runs longer to hold the same temperature; the saving is in insulation and room temperature, not in watts.
  • Leaving a device out. A UV steriliser, a second filter, or a CO2 solenoid all draw power — if it plugs in, it belongs in the form.
  • Trusting the estimate over a meter. The heater-hours guess is the weak point — a plug-in power meter for a week gives the true number.

Reference: US residential electricity prices

The US average residential price, from the Energy Information Administration's Short-Term Energy Outlook (October 2026). Your bill is what matters — this is only context for the $0.17 starting point in the form.

YearUS residential averageStatus
202416.5 cents/kWhActual
202517.3 cents/kWhActual
202618.2 cents/kWhProjected
202718.7 cents/kWhProjected

The form's starting point of $0.17/kWh sits just under the 2025 average — close enough to budget with, but read your own bill before you trust the answer. Rates vary widely by state: some states pay roughly double the national average, others well under it.

FAQ

How much does it cost to run an aquarium each month?

It depends on the heater most of all. The worked example — a 20-gallon tank with a 100 W heater, 10 W filter, 30 W light and 15 W pump at $0.17/kWh — costs $10.40/month. A nano tank with a 25 W heater can cost $2–$3/month; a large tank with a 300 W heater in a cold room can cost $30/month or more. Enter your own watts and hours to get your number.

Why is the heater most of the cost?

Because it is the biggest wattage and it runs for hours every day. In the worked example the heater is 59% of the bill. The filter and pump run 24 hours a day but at 10–15 W, so they stay cheap; the light is the only other device that can compete, and only if it is an old fluorescent at high wattage.

Should I enter the heater as 24 hours?

No — a heater cycles on a thermostat and does not run all day. 12 hours is the typical starting point. In a warm room it runs less; in a cold room, more. A plug-in power meter gives the true hours.

Where do I find my electricity rate?

On your bill. The most honest rate to enter is the total bill divided by the kWh used — that includes delivery charges, which the headline energy charge leaves out. The national average was 17.3 cents/kWh in 2025 (EIA), but your rate is what decides your cost.

Does a month mean 30 days?

Yes — a 30-day month, and a 365-day year. Real months are 28–31 days, so a February bill runs a little lower and a 31-day month a little higher; the difference is a few percent.

Will an LED light really save money?

If it replaces an old fluorescent, yes — swap the wattage in the form and read the yearly difference. A 30 W LED replacing a 60 W fluorescent running 8 hours a day saves 0.24 kWh/day, about $1.22/month or $14.90/year at $0.17/kWh.

How do I measure the real cost instead of estimating it?

Plug the whole setup — or just the heater — into a plug-in power meter for a week and read the kWh. That replaces the heater-hours guess, which is the one number in this calculator that is assumed rather than measured.

Sources

  1. U.S. Energy Information Administration — Short-Term Energy Outlook, October 2026: US average residential electricity price 17.3 cents/kWh in 2025, 18.2 cents projected for 2026, 18.7 cents for 2027 (Government). No direct link on file — listed by name.
  2. Device labels — watts read off the label on each device or its power brick (Manufacturer).
  3. TheCycledTank electricity-cost defaults — the form's starting hours (heater 12 h, filter 24 h, light 8 h, pump 24 h) and the $0.17/kWh starting rate (Our estimate).

Related tools