Work out how much GFO, high-capacity GFO or Rowaphos your system needs — in grams, tablespoons and cups — from label doses or your own phosphate readings. Get the start dose and the maintenance dose, and see the half dose to start with when phosphate is high, so a fast drop does not shock your corals. Everything runs in your browser; nothing is saved.
How it works
GFO (granular ferric oxide) pulls phosphate out of the water by binding it to iron oxide. How much you run depends on which media you hold: standard and high-capacity GFO are dosed from their label rates per gallon, while Rowaphos is worked out from your own phosphate readings and an assumed absorption capacity. This tool keeps those two methods separate, and labels every assumption as one.
Standard GFO: start 1 g per US gallon, maintenance 2 g per gallon. From the Bayoxide E33 label: 1 cup per 128 gallons to start, 1 cup per 64 gallons as the standard dose. A cup is 128 g (16 level tablespoons at 8 g each), so that is 1 g per gallon to start and 2 g per gallon for maintenance.
High-capacity GFO: 0.5 g per gallon to start. From Bulk Reef Supply: half a tablespoon per 4 gallons, against a tablespoon per 4 gallons for standard — half the standard start dose, because it holds about twice as much phosphate. The maintenance dose for high-capacity GFO is not stated on the labels found: this tool doubles the start dose (1 g per gallon), following the standard pattern. That is an assumption — check your product label.
Rowaphos: grams = (current PO₄ − target PO₄) × litres ÷ capacity. The capacity is an assumption, not a measurement: 10–20 mg of PO₄ per gram, default 15. Binding depends strongly on the phosphate concentration itself — at low phosphate near the target, Rowaphos binds far less per gram than at high phosphate — so treat the Rowaphos grams as a starting estimate and retest.
Tablespoons and cups are approximate: 8 g = 1 level tablespoon, 16 tablespoons = 1 cup. Those are the Bayoxide E33 label's figures. Other brands pack differently, so volume measures are approximate — weigh the media when it matters.
Start at half dose when phosphate is high. Do not cut phosphate by more than about 0.5 ppm in 24 hours — a rapid drop shocks corals. If your phosphate is high, or this is your first time running GFO, start at half the dose below, retest in a few days, and only then work up to the full dose.
Worked example
A 50-gallon system on standard GFO, and the same system on high-capacity GFO and Rowaphos for comparison.
50 US gal, standard GFO; Rowaphos case: 100 L, phosphate 0.5 → 0.05 ppm, capacity 15 mg/g.
Standard start = gallons × 1 g/gal; maintenance = start × 2. Rowaphos g = (0.5 − 0.05) × litres ÷ 15.
Standard start = 50 × 1 = 50 g; maintenance = 50 × 2 = 100 g; 50 ÷ 8 = 6.25 tbsp, 50 ÷ 128 = 0.39 cups; half start = 25 g. Rowaphos = 0.45 × 100 ÷ 15 = 3 g (0.38 tbsp).
50 g of standard GFO to start (6.25 tbsp), 100 g for maintenance. High-capacity instead: 25 g to start. Rowaphos for the 100 L case: 3 g.
The Rowaphos answer moves with the assumed capacity: at 10 mg/g the same 100 L case needs 4.5 g, and at 20 mg/g it needs 2.25 g. That range is the reason the capacity is shown on the page, not hidden — it is an assumption, and the true figure varies by batch and brand.
How to read your results
The verdict word is the dose in grams — the start dose, or the half start dose if you ticked that box. Under it, the pair line gives the media and the dose in tablespoons and cups, and the stat grid shows the start dose, the maintenance dose, and the half start dose (or, for Rowaphos, the grams, the capacity used, and what standard GFO would be for the same system).
A "Caution" row means slow down: do not cut phosphate by more than about 0.5 ppm in 24 hours, and if the half dose is shown, retest in a few days before working up to the full start dose. An "OK" row is a check that passed or a fact to know, such as the start and maintenance doses in grams, tablespoons and cups, or the warning that tablespoons are approximate and the media should be weighed when it matters.
For Rowaphos, the result also tells you what standard GFO would be for the same system, so the two methods can be compared directly.
Common mistakes
- Starting at the full dose with high phosphate. A rapid drop shocks corals — start at half dose, retest in a few days, and only then work up to the full dose.
- Trusting tablespoons as exact. 8 g per level tablespoon is the Bayoxide E33 label's figure; other brands pack differently. Weigh the media when it matters.
- Treating the Rowaphos capacity as a measurement. The default 15 mg/g is an assumption (range 10–20), and binding falls off at low phosphate — retest after a few days and adjust.
- Assuming the high-capacity maintenance dose is on the label. It is not stated on the labels found — this tool doubles the start dose by assumption, so check your product label.
- Trusting a low phosphate reading on its own. A kit can read low when algae are consuming phosphate, so a low reading does not always mean low phosphate in the system — judge by the reading plus algae growth.
- Dosing by the glass size. Use the actual water volume — tank minus rock, sand and equipment — not the label on the glass.
GFO dose by tank size
Grams of media to start and for maintenance, by system size. All figures recomputed with the formulae above. High-capacity maintenance is the assumed double of its start dose (see "How it works").
| Tank size | Standard start | Standard maint. | High-cap. start | Standard start (tbsp) |
|---|---|---|---|---|
| 10 gal | 10 g | 20 g | 5 g | 1.25 |
| 25 gal | 25 g | 50 g | 12.5 g | 3.13 |
| 50 gal | 50 g | 100 g | 25 g | 6.25 |
| 100 gal | 100 g | 200 g | 50 g | 12.50 |
| 200 gal | 200 g | 400 g | 100 g | 25.00 |
Read it as a scaling check: the start dose in grams is your gallons (standard) or half your gallons (high-capacity), and the maintenance dose is double the start.
FAQ
Standard GFO or high-capacity GFO — which should I use?
Both remove phosphate the same way. High-capacity holds about twice as much phosphate per gram, so its start dose is half: 0.5 g per gallon against 1 g per gallon for standard. The trade-off is that its maintenance dose is not stated on the labels found — this tool assumes double the start dose, so check your product label.
Why start at half dose?
Because a rapid phosphate drop shocks corals. Do not cut phosphate by more than about 0.5 ppm in 24 hours. If phosphate is high, or this is your first time running GFO, start at half the dose, retest in a few days, and only then work up to the full dose.
What is the Rowaphos capacity, and why is it an assumption?
Rowaphos is dosed from your phosphate readings divided by how much phosphate a gram of media can bind — assumed 10–20 mg per gram, default 15. The true figure varies by batch and brand, and binding falls off at low phosphate near the target, so the grams are a starting estimate: retest after a few days and adjust. At 10 mg/g the worked example needs 4.5 g; at 20 mg/g it needs 2.25 g.
Are tablespoons accurate enough?
Not when it matters. 8 g per level tablespoon (16 tablespoons per cup) is the Bayoxide E33 label's figure, and other brands pack differently. Tablespoons are fine for a rough start dose; weigh the media on kitchen scales when the dose matters.
My phosphate reads low but algae keeps growing. Is the reading wrong?
Possibly. A phosphate kit can read low when algae are consuming phosphate, so a low reading does not always mean low phosphate in the system. Judge by the reading plus algae growth, not the reading alone — and check food, source water and stocking, or phosphate returns after the media is spent.
How often do I replace the media?
When phosphate stops falling or starts rising again — the media is exhausted. This tool works out how much to run, not how long it lasts: that depends on how much phosphate your tank produces, so retest regularly and replace when the readings say so.
Sources
- Manufacturer — Bayoxide E33 label, via Carolina Aquatics. Standard GFO start 1 g per US gallon, maintenance 2 g per gallon; 8 g = 1 level tablespoon, 16 tablespoons = 1 cup. Used for the standard doses and the tablespoon conversions. carolinaaquatics.com
- Manufacturer — Bulk Reef Supply, "How much GFO does a reef tank need". High-capacity GFO 0.5 g per gallon to start (half a tablespoon per 4 gallons, against a tablespoon per 4 gallons for standard); do not reduce phosphate by more than 0.5 ppm in 24 hours. Used for the high-capacity start dose and the 0.5 ppm per day limit. bulkreefsupply.com
- Hobby practice — Rowaphos dosing formula, as shown by the Rowaphos calculator. Grams = (current PO₄ − target PO₄) × litres ÷ capacity, capacity 10–20 mg PO₄ per gram, default 15. Used for the Rowaphos method only; the capacity is labelled an assumption on the page. cal67.calculator.city
- Hobby practice — Holmes-Farley, R., Reefkeeping Magazine / Advanced Aquarist. Phosphate removal with GFO, aluminium oxide and lanthanum chloride; binding depends strongly on phosphate concentration. Used for the warning that Rowaphos binds far less per gram at low phosphate. (No web link on file.)