Work out how much phosphate salt raises phosphate by the amount your test says is missing — in milligrams, as a stock-solution dose, and split over enough days to stay inside your chosen daily rise. Worked example: a 100-gallon reef at 0.01 ppm phosphate needs 2.17 mL of stock (21.7 mg of monopotassium phosphate) to reach 0.05 ppm, over 2 days. Everything runs in your browser; nothing is saved.
How it works
Corals need some phosphate — a reef at a true zero starves, and phosphate is dosed in milligrams, not grams, because the amounts are so small. When your test reads below the level you want, this tool works out the weighed salt that closes the gap, from the level you measured. It never suggests a target level: the target is yours.
Phosphate needed (mg) = rise (ppm) × litres. Because 1 ppm is 1 mg per litre, the milligrams of phosphate itself are just the rise times the litres — no division by 1,000, unlike the gram-scale nitrate maths.
KH₂PO₄ (mg) = phosphate mg ÷ 0.6979; NaH₂PO₄·H₂O (mg) = phosphate mg ÷ 0.6882. A salt is not pure phosphate: monopotassium phosphate is 69.79% phosphate by weight and monosodium phosphate monohydrate is 68.82%, from their molar masses (KH₂PO₄ 136.09, NaH₂PO₄·H₂O 137.99, PO₄³⁻ 94.97). Dividing by the fraction gives the milligrams of salt to weigh.
Stock solution (mL) = salt mg ÷ (stock g × 1000 ÷ stock mL). A 1 g in 100 mL stock is 10 mg per mL, so a 21.7 mg dose is 2.17 mL of stock — measurable with a syringe, where weighing 21.7 mg of dry powder is not practical.
Days = rise ÷ max rise per day, rounded up. The default cap is 0.03 ppm per day: a 0.04 ppm rise takes 2 days. A sudden phosphate pulse feeds algae before corals can use it.
ppb phosphorus readings. Ultra-low-range checkers report phosphorus in ppb, not phosphate in ppm. The tool converts each reading first: ppm PO₄ = ppb P × 3.066 ÷ 1000 (94.97 ÷ 30.97, the PO₄ to P mass ratio). Current and target are converted independently, because a low-range checker reports ppb P while targets are usually quoted in ppm PO₄.
Worked example
A 100-gallon reef (378.5 L) testing 0.01 ppm phosphate, target 0.05 ppm, monopotassium phosphate, stock of 1 g in 100 mL, max rise 0.03 ppm per day.
378.5 L, 0.01 → 0.05 ppm phosphate, KH₂PO₄, stock 1 g in 100 mL, 0.03 ppm/day.
PO₄ mg = rise × litres. KH₂PO₄ mg = PO₄ mg ÷ 0.6979. Stock mL = salt mg ÷ 10 mg/mL. Days = rise ÷ 0.03, rounded up.
PO₄ mg = 0.04 × 378.54 = 15.14 mg. Salt = 15.14 ÷ 0.6979 = 21.7 mg. Stock = 21.7 ÷ 10 = 2.17 mL. Days = 0.04 ÷ 0.03 = 1.3 → 2 days, so 2.17 ÷ 2 = 1.09 mL per day.
2.17 mL of stock (21.7 mg KH₂PO₄), 1.09 mL per day over 2 days, raising phosphate from 0.01 to 0.05 ppm.
The same rise with monosodium phosphate monohydrate needs 15.14 ÷ 0.6882 = 22.0 mg. And from a ppb reading of 10 ppb P (0.03066 ppm PO₄) to the same 0.05 ppm target, the rise is only 0.01934 ppm: 7.3 mg of phosphate, 10.5 mg of salt, 1.05 mL of stock, in 1 day.
How to read your results
The verdict word is the dose in milligrams — the headline number to weigh or to draw up as stock. Under it, the pair line names the salt and the daily stock dose, and the stat grid shows the salt dose, the total stock in millilitres, and the milligrams per day.
If the verdict says "No dose needed", phosphate is already at or above your target — do not dose to push it higher. A "Caution" row means the correction is split over days on purpose, or that phosphate-removing media (GFO) must come offline first, or the dose disappears into the media. An "OK" row is a check that passed, such as the whole correction fitting inside one safe daily rise.
Test again between doses. Hobby colour kits struggle at these levels — a digital low-range checker makes the dose meaningful.
Common mistakes
- Weighing the dry salt directly. A 21.7 mg dose is too small for kitchen scales — make a stock solution (1 g in 100 mL is 10 mg per mL) and measure millilitres instead.
- Dosing while GFO is running. The dose disappears into the media — pull phosphate-removing media offline first.
- Reading a ppb phosphorus number as ppm phosphate. A 10 ppb P reading is only 0.03066 ppm as PO₄ — dosing from the unconverted number over-doses by about thirty times.
- Dosing the whole correction at once. A sudden phosphate pulse feeds algae before corals can use it — split it at 0.03 ppm per day or less.
- Storing stock solution forever. Label the bottle with its strength and date, keep it in the fridge, and remake it every few months.
- Chasing zero phosphate. Corals need some phosphate detectable — the tool doses to a target you chose, never to zero.
Phosphate salt per 0.01 ppm rise
Milligrams of KH₂PO₄ and millilitres of a 1 g in 100 mL stock (10 mg/mL) to raise phosphate by 0.01 ppm, by system size. All figures recomputed with the formulae above.
| Tank size | KH₂PO₄ | Stock (10 mg/mL) |
|---|---|---|
| 25 gal | 1.36 mg | 0.14 mL |
| 50 gal | 2.71 mg | 0.27 mL |
| 75 gal | 4.07 mg | 0.41 mL |
| 100 gal | 5.42 mg | 0.54 mL |
| 150 gal | 8.14 mg | 0.81 mL |
| 200 gal | 10.85 mg | 1.08 mL |
Read it as a scaling check, not as a dose: multiply the row for your tank size by the rise you need in hundredths of a ppm, then split it over days at your daily cap.
FAQ
Why is phosphate dosed in milligrams?
Because the amounts are tiny: raising a 100-gallon reef by 0.04 ppm takes only 21.7 mg of salt. Kitchen scales cannot weigh that reliably, which is why the tool works through a stock solution — 1 g in 100 mL is 10 mg per mL, so the dose becomes 2.17 mL, easy to measure with a syringe.
My checker reads ppb phosphorus. Is that the same as ppm phosphate?
No. A 10 ppb P reading is 0.03066 ppm as PO₄ — the tool multiplies ppb P by 3.066 and divides by 1,000. Enter the reading with its own unit (ppm PO₄ or ppb P) for current and target separately, and the conversion happens before the maths starts.
Potassium or sodium phosphate — does it matter?
Hardly, at these amounts: the same rise needs 21.7 mg of monopotassium phosphate or 22.0 mg of monosodium phosphate monohydrate. Use whichever salt you hold — the tool shows both so you never have to re-do the maths.
Why split the dose over days?
A sudden phosphate pulse feeds algae before corals can use it. The default cap is 0.03 ppm per day, so a 0.04 ppm rise takes 2 days. Test again between doses.
Do I need to turn my GFO off?
Yes — pull phosphate-removing media offline first, or the dose disappears into the media. Put it back once the level is where you want it and the dose has had time to work.
How accurate is my phosphate test at these levels?
Not very, with a hobby colour kit — they struggle below about 0.05 ppm. A digital low-range checker makes the dose meaningful; with a colour kit, treat the reading as approximate and retest before dosing again.
Sources
- Textbook — Haynes (ed.), CRC Handbook of Chemistry and Physics. Molar masses used for the salt fractions: KH₂PO₄ 136.09, NaH₂PO₄·H₂O 137.99, PO₄³⁻ 94.97, P 30.97. Used for the 0.6979, 0.6882 and 3.066 figures.
- Hobby practice — Holmes-Farley, R., Reefkeeping Magazine / Advanced Aquarist. Phosphate as a coral nutrient, and the problems of very low levels. Used for the cautions about keeping phosphate detectable and pulling GFO offline before dosing.
No web link is given for these sources because none is on file — the figures come from the printed references named above.