Convert a hardness reading between dGH, dKH, ppm as CaCO3, meq/L, mmol/L, grains per gallon, French degrees and Clark degrees — and see the value in all eight units at once, with the USGS band. Worked example: 8 dGH = 142.8 ppm = 2.853 meq/L = 8.341 gpg. One plain warning on the page: GH and KH measure different things, so a GH number converted into dKH units is not a KH reading. Everything runs in your browser; nothing is saved.
How it works
Every unit converts through ppm as CaCO3, the common unit. First the tool turns your number into ppm — multiply by the factor for the unit it is in — then it turns that ppm into every other unit by dividing by each unit's factor. There is no separate formula per pair of units; one hub unit keeps all eight consistent.
The factors (ppm as CaCO3 per 1 unit). 1 dGH = 1 dKH = 17.848 ppm; 1 meq/L = 50.044 ppm; 1 mmol/L = 100.09 ppm; 1 gpg = 17.118 ppm; 1 °f = 10 ppm; 1 °Clark = 14.254 ppm. Each one is a published definition, not a rounded guess — see Sources. The round figures you may see elsewhere (17.86, 50, 100, 17.1, 14.3) are these same values rounded; the tool uses the precise ones, so a round trip through the converter returns your starting number.
Why dGH and dKH share a factor. Both are German degrees — 1 °dH is defined as 10 mg/L of calcium oxide, which is 17.848 mg/L as CaCO3 — so the arithmetic is identical. But they measure different things: dGH counts calcium + magnesium, dKH (alkalinity) counts buffering, mostly bicarbonate. Converting a GH number into dKH units only restates the same number; it does not tell you your KH.
The USGS band. The tool also reads the ppm value against the US Geological Survey bands: soft 0–60 ppm, moderately hard 61–120 ppm, hard 121–180 ppm, very hard over 180 ppm. The band describes the water, not a verdict — soft water suits some fish and hard water suits others, so read the band with the table below.
Worked example
A European test kit reads 8 dGH. Convert it to every other unit.
8 dGH, converting to ppm as CaCO3, meq/L, mmol/L, gpg, French degrees and Clark degrees.
ppm = value × factor of the unit it is in. Each other unit = ppm ÷ its factor.
8 × 17.848 = 142.784 ppm. Then 142.784 ÷ 50.044 = 2.853 meq/L; ÷ 100.09 = 1.427 mmol/L; ÷ 17.118 = 8.341 gpg; ÷ 10 = 14.28 °f; ÷ 14.254 = 10.02 °Clark.
142.8 ppm as CaCO3 — hard water on the USGS scale (121–180 ppm). The same number is 8 dKH numerically, but that is not a KH reading.
A second check, from an American water report: 12 gpg × 17.118 = 205.4 ppm; 205.4 ÷ 17.848 = 11.51 dGH; 205.4 ÷ 10 = 20.54 °f; 205.4 ÷ 14.254 = 14.41 °Clark; 205.4 ÷ 100.09 = 2.052 mmol/L — very hard, over the 180 ppm line.
And a drop-kit check: most KH/GH drop kits count 1 drop = 1 degree, so 6 drops = 6 dKH = 6 × 17.848 = 107.1 ppm — moderately hard. Some kits give the drop value in ppm instead (17.9 ppm per drop is the same 1 degree); read the leaflet, and use the ppm figure if that is what it prints.
How to read your results
The headline is the value in ppm as CaCO3, with the USGS band beside it. The stat grid repeats the three numbers that matter most: the ppm value, the German-degree value, and the band with its ppm limits. Below that, the table lists all eight units — your input row is marked, so you can check the conversion ran from the unit you meant.
Read the band as a description, then match it to the fish in the table below. Soft water (0–60 ppm, about 0–3.4 dGH) suits tetras, rasboras, discus and Caridina shrimp; moderately hard water (61–120 ppm, about 3.4–6.7 dGH) suits most community fish and Neocaridina shrimp; hard water (121–180 ppm, about 6.8–10.1 dGH) suits livebearers, goldfish and many barbs; very hard water (over 180 ppm, over 10.1 dGH) suits Rift Lake cichlids and brackish species. Those are typical matches, not rules — a species' own care guide is the authority.
What to do next depends on why you converted. Comparing a fish profile against your tap water: compare in ppm, the unit both sides can be put into. Dosing KH: do not use the dKH row from a GH reading — measure KH with a KH kit first, then use the KH / pH Buffer Dosing Calculator.
Common mistakes
- Treating a converted GH number as a KH reading. Same factor, different measurement — GH is calcium + magnesium, KH is buffering.
- Comparing a gpg number against a dGH target without converting. They look close (17.118 vs 17.848 ppm) but 10 gpg is only about 9.6 dGH, not 10.
- Using the rounded °Clark figure (14.3) and the precise one (14.254) interchangeably in the same chain. The gap is only 0.3%, but mixing them makes round trips drift.
- Reading the USGS band as a verdict. "Very hard" is not bad water — Rift Lake cichlids need it, and soft-water fish need the opposite.
- Forgetting that a drop-kit drop is not always 1 degree. Some kits count half a degree per drop, and some print the drop value in ppm — check the leaflet.
- Converting TDS or conductivity into hardness. TDS is a different measurement; use the TDS / Conductivity Converter for that, and this converter for hardness.
- Assuming a water-softener reading in gpg is already dGH. Softener companies use gpg; fish profiles use dGH — convert before comparing.
Conversion table
German degrees to the other common units, computed with the tool's own factors.
| dGH | ppm as CaCO3 | meq/L | gpg | °f |
|---|---|---|---|---|
| 1 | 17.8 | 0.357 | 1.04 | 1.78 |
| 2 | 35.7 | 0.713 | 2.09 | 3.57 |
| 4 | 71.4 | 1.427 | 4.17 | 7.14 |
| 6 | 107.1 | 2.140 | 6.26 | 10.71 |
| 8 | 142.8 | 2.853 | 8.34 | 14.28 |
| 10 | 178.5 | 3.566 | 10.43 | 17.85 |
| 12 | 214.2 | 4.280 | 12.51 | 21.42 |
| 15 | 267.7 | 5.350 | 15.64 | 26.77 |
| 20 | 357.0 | 7.133 | 20.85 | 35.70 |
USGS hardness bands
The bands the tool reports, with the fish that typically suit each one.
| Band | ppm as CaCO3 | dGH | Fish that typically suit it |
|---|---|---|---|
| Soft | 0–60 | 0–3.4 | Tetras, rasboras, discus, Caridina shrimp |
| Moderately hard | 61–120 | 3.4–6.7 | Most community fish, Neocaridina shrimp |
| Hard | 121–180 | 6.8–10.1 | Livebearers, goldfish, many barbs |
| Very hard | Over 180 | Over 10.1 | Rift Lake cichlids, brackish species |
FAQ
Is dGH the same as dKH?
No. They share the same German-degree factor (17.848 ppm as CaCO3 per degree), so the numbers convert identically — but dGH measures calcium + magnesium and dKH measures buffering, mostly bicarbonate. A GH reading converted into dKH units is still a GH reading, not a KH reading.
What is a grain per gallon (gpg)?
An old American unit still used by water-softener companies: 1 grain of CaCO3 (64.8 mg) dissolved in 1 US gallon (3.79 L) is 17.118 ppm as CaCO3. It is almost the same size as a German degree (17.848 ppm) — 10 gpg is about 9.6 dGH — but close is not equal, so convert before comparing.
What counts as soft or hard water?
On the USGS scale: soft is 0–60 ppm as CaCO3, moderately hard 61–120 ppm, hard 121–180 ppm, very hard over 180 ppm. In German degrees that is about 0–3.4, 3.4–6.7, 6.8–10.1 and over 10.1 dGH. The band is a description of the water, not a verdict — different fish need different bands.
How do drop test kits convert to ppm?
Most drop kits count 1 drop = 1 degree, so 6 drops = 6 dKH = 107.1 ppm. Some kits give the drop value in ppm instead (17.9 ppm per drop is the same 1 degree), and some fine-resolution kits count half a degree per drop. Read the leaflet for the drop value, then convert with this tool.
Why does this tool use 14.254 ppm for °Clark when some tables say 14.3?
14.254 ppm is the definition: 1 grain (64.8 mg) per Imperial gallon (4.546 L). Tables that print 14.3 have rounded it. The difference is 0.3% — negligible for aquarium use — but the tool uses the definition-based figure so round trips through the converter come back exact.
Does converting change my water?
No. This converter only restates a reading in a different unit. To actually change hardness, use the GH / KH Remineralisation Calculator to raise GH from RO water, or the KH / pH Buffer Dosing Calculator to raise KH.
Sources
- Reference — Wikipedia, "Hard water". en.wikipedia.org/wiki/Hard_water Used for the conversion table and the unit definitions: 1 dGH = 17.848 ppm, 1 mmol/L = 100.09 ppm, 1 gpg = 17.118 ppm, 1 °f = 10 ppm, 1 °Clark = 14.254 ppm.
- Reference — 123calculus, water hardness conversion table. 123calculus.com Used as the second source for every factor, including 1 meq/L = 50.044 ppm.
- Government — USGS, Hardness of Water. Used for the bands: soft 0–60, moderately hard 61–120, hard 121–180, very hard over 180 mg/L as CaCO3.
- Standard — DIN 38409. Used for the German-degree definition: 1 °dH = 10 mg/L CaO = 17.848 mg/L CaCO3.
- Reference — Haynes (ed.), CRC Handbook of Chemistry and Physics. Used for the molar mass of CaCO3 (100.09 g/mol, so 1 mmol/L = 100.09 mg/L and 1 meq/L = 50.04 mg/L) and the grain (64.79891 mg), giving 1 gpg = 17.118 mg/L.
- Hobby practice — OwnerSpec, water hardness unit converter. ownerspec.com Used only as a cross-check for all factors; it also notes the Water Quality Association glossary figure of 17.1 ppm per gpg.