Turn a target GH and KH into weighed grams for a bucket of RO/DI water — for shrimp and planted tanks. Pick DIY salts, a Salty Shrimp label dose, or your own product's label dose, and see the Ca:Mg ratio and the TDS rise before the water goes in the tank. For example, 10 litres of RO water raised 4 dGH with calcium sulphate alone needs 1.23 g of CaSO4, and the TDS rises about 96 ppm. Mix the salts into the RO water in a separate container, test GH and KH, and only then use it — never add dry powder to a stocked tank. Everything runs in your browser; nothing is saved.
How it works
DIY salts are molar chemistry. 1 dGH = 17.85 mg/L as CaCO3 = 7.15 mg/L Ca2+ = 4.34 mg/L Mg2+. 1 dKH = 21.8 mg/L HCO3-. The salts: calcium sulphate dihydrate (CaSO4·2H2O) is 23.3% calcium, so 7.15 ÷ 0.233 = 30.7 mg per litre per dGH; magnesium sulphate heptahydrate (MgSO4·7H2O, Epsom salt) is 9.86% magnesium, so 4.34 ÷ 0.0986 = 44.0 mg per litre per dGH; potassium bicarbonate (KHCO3) is 61% bicarbonate, so 21.8 ÷ 0.61 = 35.7 mg per litre per dKH; potassium carbonate (K2CO3) needs 24.7 mg per litre per dKH. Grams = mg/L per degree × degrees × litres ÷ 1,000.
Calcium share. The GH rise is split between calcium and magnesium — the default is 70% calcium / 30% magnesium, which gives a Ca:Mg ratio of about 3.84:1 by weight. A Ca:Mg ratio near 3–4:1 by weight is the usual planted/shrimp starting point. You can pick 50/50, all calcium, or all magnesium instead.
TDS and conductivity. The TDS rise counts the ions only (water of crystallisation does not count): about 24 ppm per dGH of CaSO4, about 21.5 ppm per dGH of MgSO4, about 36 ppm per dKH of KHCO3, about 24.7 ppm per dKH of K2CO3. Conductivity is estimated from TDS on the 442 scale (EC ≈ TDS ÷ 0.64) and is approximate — conductivity per ppm varies by salt mix. Confirm with a TDS meter after mixing.
Commercial products use the label only. Salty Shrimp Bee Shrimp Mineral GH+ (GH-only): an evenly full measuring spoon (about 3 g) to 20 litres reaches about 6 dGH and about 200 ± 50 µS/cm, with KH essentially unchanged. Salty Shrimp Shrimp Mineral GH/KH+: an evenly full measuring spoon (about 2 g) to 10 litres reaches about 6 dGH and about 300 ± 50 µS/cm, at a fixed dGH/KH ratio of 1.0/0.5. A custom product scales from the grams per 10 litres and the dGH (and dKH, if any) that dose reaches — from its own label, never guessed. No TDS or conductivity figure is shown for a custom product, because the label dose does not state one.
Starting hardness is subtracted. If the water already has some GH or KH, the tool doses only the rise to target. Pure RO/DI water starts at 0 dGH / 0 dKH.
Worked example
10 litres of RO water, raised 4 dGH with calcium sulphate only (100% calcium, no magnesium, no KH).
Volume 10 L RO water (0 dGH / 0 dKH), target GH 4 dGH, target KH 0 dKH, DIY salts, 100% calcium share.
CaSO4 grams = dGH × 30.7 mg/L × litres ÷ 1,000. Calcium added = dGH × 7.15 mg/L. TDS rise = dGH × 24 ppm.
CaSO4 = 4 × 30.7 × 10 ÷ 1,000 = 1.23 g. No MgSO4 in a calcium-only mix. Calcium added = 4 × 7.15 = 28.6 mg/L. TDS rise = 4 × 24 = 96 ppm.
1.23 g of calcium sulphate dihydrate, TDS up about 96 ppm. A calcium-only mix is a short-term fix, not a standing recipe — shrimp and plants also need magnesium.
The usual mix instead: the 70/30 default on the same 10 litres raised 5 dGH needs 1.07 g of CaSO4 and 0.66 g of MgSO4, for a Ca:Mg ratio of 3.84:1 by weight. And a KH example: 10 litres raised 2 dKH needs 0.714 g of KHCO3 (TDS up about 71.4 ppm) or 0.494 g of K2CO3 — less salt, but K2CO3 pushes pH higher than KHCO3 for the same KH rise.
Cross-check: the FishLore RO recipe (0.386 g CaSO4 + 0.384 g MgSO4 + 0.135 g KHCO3 per US gallon, 3.785 L) is quoted as about 5.6 dGH + 1 dKH. This calculator's chemistry reproduces it: CaSO4 gives 386 ÷ 30.7 ÷ 3.785 = 3.32 dGH, MgSO4 gives 384 ÷ 44.0 ÷ 3.785 = 2.31 dGH (total 5.63 dGH), and KHCO3 gives 135 ÷ 35.7 ÷ 3.785 = 1.00 dKH, with a TDS rise of about 165 ppm. The recipe's Ca:Mg split is about 59% calcium / 41% magnesium by dGH, not the 70/30 default used here.
How to read your results
The verdict word is the total dose in grams — total salts for DIY, or the product name and grams for a commercial or custom product. Under it, the pair line shows the volume and the GH and KH the water will reach.
The stat grid shows the three numbers that decide the water: the resulting GH, the resulting KH, and the TDS rise (with the estimated conductivity where the tool can work it out). Below the stats, the dose table lists each salt, its weighed grams, and what it does. Below the table, the checks are grouped. "Caution" is a risk — read it before you start. "OK" means that check passed.
Watch for the fixed-ratio warning: a GH/KH+ product raises GH and KH together at a fixed 1.0/0.5 ratio, so it cannot hit every GH and KH pair. If the warning appears, dose to the parameter that matters most for your shrimp, then test — do not chase both numbers with that product. What to do next: dissolve the salts in the RO water, stir until dissolved (calcium sulphate dissolves slowly and may look cloudy at first), and test GH and KH with your kits before the water goes anywhere near the tank.
Common mistakes
- Adding dry powder to a stocked tank. Mix the salts into the RO water in a separate container, test it, and only then use it.
- Dissolving calcium salt and baking soda together as concentrates. Mixed as concentrates they can form chalky calcium carbonate — dissolve them in separate cups before adding them to the bucket.
- Chasing both numbers with a GH/KH+ product. Its fixed 1.0/0.5 ratio means one dose cannot hit every GH and KH pair — dose to the parameter that matters most, then test.
- Dosing KH for Caridina shrimp on active soil. They usually want KH 0–1 — check the Shrimp Parameter Checker before dosing any KH at all.
- Working out the dose for the whole tank instead of the bucket. This tool remineralises the water-change water, not the tank.
- Weighing under 0.1 g on a kitchen scale. Use a 0.01 g jewellery scale, or mix a larger batch and keep the extra remineralised water for the next change.
- Running a calcium-only mix as a standing recipe. Shrimp and plants also need magnesium — the 70/30 default exists for a reason.
- Treating the TDS or EC figure as exact. The TDS rise is an ion-sum estimate and the EC uses the 442 scale; a meter reading can differ, so measure after mixing.
Salt per degree
Grams of each salt for a 1-degree rise, at the tool's own stoichiometric figures (1 US gallon = 3.785 L).
| Salt | Per degree | Per 10 L | Per 10 US gal |
|---|---|---|---|
| Calcium sulphate dihydrate (CaSO4·2H2O) | 30.7 mg/L per dGH | 0.31 g | 1.16 g |
| Magnesium sulphate heptahydrate (MgSO4·7H2O) | 44.0 mg/L per dGH | 0.44 g | 1.67 g |
| Potassium bicarbonate (KHCO3) | 35.7 mg/L per dKH | 0.36 g | 1.35 g |
| Potassium carbonate (K2CO3) | 24.7 mg/L per dKH | 0.25 g | 0.93 g |
Salty Shrimp label doses
The two commercial options in this tool, from the product labels. If your tub says otherwise, the tub wins.
| Product | Label dose | Reaches | Conductivity | KH |
|---|---|---|---|---|
| Bee Shrimp Mineral GH+ | About 3 g per 20 L | About 6 dGH | About 200 ± 50 µS/cm | Essentially unchanged |
| Shrimp Mineral GH/KH+ | About 2 g per 10 L | About 6 dGH | About 300 ± 50 µS/cm | About 3 dKH (fixed 1.0/0.5 ratio) |
FAQ
Why two salts instead of one?
GH is calcium plus magnesium together. The default 70/30 split gives a Ca:Mg ratio near 3.84:1 by weight, the usual planted/shrimp starting point. A calcium-only mix leaves magnesium out, which shrimp and plants need — it is a short-term fix, not a standing recipe.
What Ca:Mg ratio should I use?
3:1 by weight (the 70/30 default) is the usual starting point and matches many natural soft waters and commercial shrimp minerals. 4:1 suits hard-water livebearers; 2:1 gives more magnesium, which some planted-tank keepers prefer. The ratio changes the grams of each salt, not the total GH.
Why does the calcium sulphate dissolve so slowly?
Calcium sulphate is only sparingly soluble (about 2 g/L). Stir well and give it time; it may look cloudy at first. Magnesium sulphate (Epsom salt) dissolves fast. For large batches or high GH, a calcium chloride product dissolves more easily — but this tool only calculates the sulphate salts, so check that product's own label.
Why can't the GH/KH+ product hit both my targets?
It raises GH and KH together at a fixed 1.0/0.5 ratio — one dose, two numbers, no independent control. If your targets do not sit on that ratio, dose to the parameter that matters most for your shrimp, then test. Do not chase both numbers with that product.
Does raising GH change pH?
Hardly at all. Calcium sulphate and Epsom salt are neutral salts — they raise GH and TDS without moving pH. To change pH, adjust KH instead (see the KH/pH Buffer Calculator and the pH Calculator).
Can I use tap water instead of RO water?
Yes, if you only need softer water rather than mineral-free water — blending RO with tap is cheaper than full remineralisation (see the RO Water Calculator). Enter the tap water's GH and KH as the starting values and the tool doses only the rise. To add KH to existing tank water, use the KH/pH Buffer Calculator.
Why is there no TDS figure for my custom product?
The label dose does not state one, and this tool never guesses it. Measure TDS with a meter after mixing, before the water goes in the tank.
Sources
- Standard — DIN 38409. 1 dGH = 10 mg/L CaO = 0.1783 mmol/L Ca + Mg. Used for the degree-to-millimoles step.
- Standard — APHA/AWWA/WEF, Standard Methods, Method 2340: Hardness. Total hardness as the sum of calcium and magnesium.
- Textbook — Haynes (ed.), CRC Handbook of Chemistry and Physics. Molar masses: calcium sulphate dihydrate 172.17, magnesium sulphate heptahydrate 246.47, sodium bicarbonate 84.007. Used for the grams-per-degree figures.
- Government — USGS, Hardness of Water. Calcium and magnesium as the minerals behind hardness.
- Manufacturer — Salty Shrimp Bee Shrimp Mineral GH+ label (about 3 g per 20 litres reaches about 6 dGH and about 200 ± 50 µS/cm, KH essentially unchanged) and Shrimp Mineral GH/KH+ label (about 2 g per 10 litres reaches about 6 dGH and about 300 ± 50 µS/cm, dGH/KH ratio 1.0/0.5), as reproduced by Aquarium Shrimp Keeping / Ariumology and Blackwater Aquariums. If your tub says otherwise, the tub wins.
- Hobby practice — FishLore forum thread "RO beginner". The RO recipe (0.386 g CaSO4 + 0.384 g MgSO4 + 0.135 g KHCO3 per US gallon, quoted as about 5.6 dGH + 1 dKH) used only as a cross-check of the stoichiometric math above, never as the authority for a figure.
- Hobby practice — aquarium.tools. TDS rise figures (about 24 ppm per dGH of CaSO4, about 21.5 ppm per dGH of MgSO4, about 36 ppm per dKH of KHCO3), via the site research report.