Nutrient Unit Converter

From your test kit or lab report — zero or more
Check the kit box or colour chart — API reads NO3, NT Labs reads NO3-N
Hanna HI736 phosphorus reads in ppb; most kits read in ppm
The form your guide, dosing chart or forum post uses
1 ppm = 1,000 ppb

NO3 = NO3-N × 4.43, NO2 = NO2-N × 3.29, NH3 = NH3-N × 1.21, NH4+ = NH3 × 1.06 (NT Labs; ALS Global molecular weights 17.03/18.04); PO4 = P × 3.066 (Hach; Hanna 95/31); 1 ppm = 1,000 ppb. Example: 20 ppm NO3-N = 88.6 ppm NO3; 100 ppb P = 0.31 ppm PO4 (the Hanna HI736 reading). API kits report nitrate as NO3 and phosphate as PO4; NT Labs kits and lab reports use the -N forms — check your kit before comparing numbers. This converts orthophosphate only; total phosphorus needs a digestion step and is a different test.

Your converted reading

Enter a reading and pick the forms — the same water in the form you asked for appears here.

Why use this calculator?

  • Convert a reading to the form your guide, dosing chart or forum post uses — no more 4.4× mistakes.
  • Handles the Hanna HI736 case in one step: ppb phosphorus to ppm phosphate.
  • Covers nitrate, nitrite, phosphate and ammonia forms in one place, including NH3 to NH4+.
  • Shows which form each major kit reports, so you convert in the right direction.

Work out the toxic share of an ammonia reading with the Free Ammonia Calculator, or check the reading itself with the Water Parameter Checker. · Back to Water Chemistry

Convert a nitrate, nitrite, phosphate or ammonia reading between the ion form and the as-nitrogen / as-phosphorus form — and between ppm and ppb — so you can compare your kit against any guide or dosing chart without a 4.4× mistake. For example, 20 ppm NO3-N is 88.6 ppm NO3, and a Hanna HI736 reading of 100 ppb phosphorus is about 0.31 ppm phosphate. Everything runs in your browser; nothing is saved.

How it works

The tool converts through the "as N" or "as P" basis. First it turns your reading into its element basis — divide by the factor for the form it is in — then it turns that basis into the form you asked for by multiplying by that form's factor. Nitrogen forms convert among themselves and phosphorus forms convert between each other; a nitrogen reading cannot become a phosphorus one, and the tool refuses that conversion instead of guessing.

The factors. NO3 = NO3-N × 4.43; NO2 = NO2-N × 3.29; NH3 = NH3-N × 1.21 (all three printed by NT Labs); NH4+ = NH3 × 1.06 (from the ALS Global molecular weights, 18.04 / 17.03); PO4 = P × 3.066 (Hach; Hanna's 95 / 31). The element form is always the smaller number, because it leaves out the oxygen and hydrogen — that is why the same water reads 4.43× higher as NO3 than as NO3-N.

ppm and ppb. 1 ppm = 1,000 ppb, by definition. The unit change is a separate ×1,000 step on top of the form factor — the Hanna HI736 case needs both at once: ppb phosphorus to ppm phosphate is × 3.066 ÷ 1,000.

Rounding, stated plainly. The tool uses the kit-printed factors (4.43, 3.29, 1.21, 1.06, 3.066), and the exact molar-mass ratios differ slightly: NO3 is 62.00 / 14.01 = 4.425, NH3 is 17.03 / 14.01 = 1.216, and NH4+ to its "as N" basis by the direct ratio is 18.04 / 14.01 = 1.2876, while the tool's compounded path (÷ 1.06, then ÷ 1.21) gives 1.2826. Those gaps are 0.2–0.5% — far below test-kit accuracy — and compounding keeps the tool self-consistent, so converting NH3 to NH4+ and back returns the starting number exactly.

What it does not do. It only changes the mass label. It does not tell you whether ammonia is toxic — that share depends on pH and temperature, which is the Free Ammonia Calculator's job — and it converts orthophosphate only: total phosphorus needs a digestion step and is a different test.

Worked example

A lab report shows 20 ppm NO3-N (nitrate-nitrogen). What would a hobby nitrate kit read?

Inputs

20 ppm NO3-N, converting to NO3 in ppm.

Formula

NO3 = NO3-N × 4.43.

Calculation

20 × 4.43 = 88.6 ppm NO3.

Result

88.6 ppm NO3 — what an API kit would read for the same water. Back the other way: 88.6 ÷ 4.43 = 20.0 ppm NO3-N.

The Hanna HI736 case, both conversions at once: 100 ppb P ÷ 1,000 = 0.1 ppm P, then 0.1 × 3.066 = 0.3066 ppm PO4 (about 0.31 ppm). Hanna's own range check agrees: 200 ppb P = 0.613 ppm PO4.

Two more, from the same factors: 1.00 ppm NH3 × 1.06 = 1.06 ppm NH4+, and back 1.06 ÷ 1.06 = 1.00 ppm NH3. And 0.5 ppm NO2-N × 3.29 = 1.645 ppm NO2.

How to read your results

The headline is the converted value in the form and unit you asked for. The stat grid shows the three things that explain it: the converted value, your original reading, and the form factor between them (for example × 4.43 for NO3-N to NO3). The factor shown is the form factor only — if you also changed units, the ×1,000 ppm/ppb step is noted beside it.

Before you act on the number, check the form your guide uses. Most hobby nitrate kits read NO3 and most phosphate kits read PO4; lab reports, ICP tests and many European kits use NO3-N and PO4-P; Hanna phosphorus checkers read ppb P. If the label says "-N", "as N", "-P" or "as P", it is the element form — convert it to the ion form before comparing it with a kit reading.

For ammonia, remember the reading is total ammonia (NH3 + NH4+). This converter only relabels the mass; which share is toxic NH3 depends on pH and temperature, so use the Free Ammonia Calculator for that. For phosphate, remember this is orthophosphate only — converting PO4-P to PO4 does not give total phosphorus.

Common mistakes

  • Comparing a NO3 number against a NO3-N target without converting. The same water reads 4.43× higher as NO3 — a "20 ppm" limit means 20 ppm NO3, or only about 4.5 ppm NO3-N.
  • Reading a Hanna HI736 result as ppm phosphate. It reads ppb phosphorus: 100 ppb P is about 0.31 ppm PO4, not 100 ppm — convert both the unit and the form.
  • Forgetting the ×1,000 when only the unit changes. 0.05 ppm is 50 ppb; the form factor does not apply when the form stays the same.
  • Treating NH3-N as toxic ammonia. NH3-N is total ammonia expressed as nitrogen; which share is toxic NH3 depends on pH and temperature.
  • Assuming a phosphate conversion gives total phosphorus. This converts orthophosphate only; total phosphorus needs a digestion step and is a different test.
  • Mixing the kit-printed factor with the exact molar-mass ratio in the same chain. 1.21 vs 1.216 and 1.2826 vs 1.2876 differ by under 0.5% — pick one path and let the tool do it, rather than hand-converting halfway.
  • Converting nitrogen into phosphorus (or the reverse). They are different elements; the tool refuses that conversion, and no factor makes it valid.

Nitrate table

Nitrate as NO3 to nitrate-nitrogen, at the tool's 4.43 factor, with the usual reading of each level.

NO3 (ppm)NO3-N (ppm)Typical meaning
51.13Low — reef or well-planted tank
102.26Good for most tanks
204.51Fine for most fish; change water soon
409.03Upper limit for most freshwater fish
8018.06High — change water, find the cause

Phosphate table

Phosphate as PO4 to phosphorus, at the tool's 3.066 factor, with the usual reading of each level.

PO4 (ppm)P (ppm)P (ppb)Typical meaning
0.030.01010Low reef target
0.10.03333Common reef target
0.250.08282High for reef, fine fish-only
0.50.163163Lean-dosed planted tank
10.326326Planted tank, regular fertiliser
20.652652Rich planted dosing, strong light + CO2

FAQ

What is the difference between nitrate and nitrate-nitrogen?

They are the same water, weighed two ways. NO3 is the whole nitrate ion (nitrogen + oxygen); NO3-N counts only the nitrogen in it. The ion is 4.43× heavier, so 20 ppm NO3-N is 88.6 ppm NO3. Lab reports use the -N form; most hobby kits use the ion form.

How do I convert phosphate to phosphorus?

Multiply by 3.066 going from P to PO4, or divide by 3.066 going the other way: 0.5 ppm P is 1.533 ppm PO4, and 1 ppm PO4 is 0.326 ppm P. If the reading is in ppb, divide by 1,000 first — 100 ppb P is 0.1 ppm P, which is about 0.31 ppm PO4.

Which form does my test kit use?

API nitrate kits read NO3, API phosphate kits read PO4, and API ammonia reads total ammonia (NH3 + NH4+). NT Labs kits and laboratory reports use the -N forms. Hanna's HI713 reads ppm PO4; Hanna's HI736 reads ppb P. Check the kit box or colour chart — it prints the form.

Is NH3-N the same as total ammonia?

Yes, expressed as nitrogen: NH3-N is total ammonia (NH3 + NH4+) weighed as nitrogen only. 1 ppm NH3-N is 1.21 ppm as NH3 and about 1.28 ppm as NH4+ on this tool's factors. All three describe the same water; only the bookkeeping changes.

What nitrate level is safe?

Most freshwater fish are kept under 20–40 ppm NO3 (about 4.5–9.0 ppm NO3-N). Sensitive fish, shrimp and fry do better under 10–20 ppm NO3, and reef tanks with corals usually run about 1–10 ppm NO3. Those are typical targets from the conversion guides, not a diagnosis — a rising trend matters more than one reading.

Does this tell me if my ammonia is toxic?

No. This converter only changes the mass label. Whether ammonia is toxic depends on how much of it is NH3, and that share depends on pH and temperature — use the Free Ammonia Calculator for that. A test-kit ammonia reading is total ammonia either way.

Why does the tool use 1.21 when the molecular weights give 1.216?

Because 1.21 is the figure NT Labs prints on its kits — the one hobby keepers actually meet. The exact ratio (17.03 / 14.01 = 1.216) differs by 0.5%, and the same rounding applies to NH4+: the tool's compounded 1.2826 vs the direct 1.2876. Both gaps are far below test-kit accuracy, and using the printed factors keeps every path through the tool self-consistent.

Sources

  1. Manufacturer — NT Labs, nitrate test. nt-labs.com Used for the 4.43 factor and for NT Labs kits reporting as NO3-N.
  2. Manufacturer — NT Labs, Aquarium Lab multi-test. nt-labs.com Used for the 1.21 (NH3-N), 3.29 (NO2-N) and 4.43 (NO3-N) factors, and for NT Labs reporting in the -N forms.
  3. Manufacturer — Hach, phosphate / phosphorus troubleshooting guide. manuals.plus Used for PO4 = P × 3.066 (reverse 0.3261) and for total phosphorus needing a digestion step.
  4. Manufacturer — Hanna Instruments, via Reef2Reef. reef2reef.com Used for PO4 = 95 / 31 = 3.066, the HI713 reading ppm PO4, the HI736 reading ppb P, and ppb ÷ 1,000 = ppm.
  5. Manufacturer / Laboratory — ALS Global, EnviroMail 43. alsglobal.com Used for the molecular weights (N 14.01, NH3 17.03, NH4+ 18.04), the NH4+ = NH3 × 1.06 factor, and laboratory reports using the "as N" convention.
  6. Manufacturer — API Reef Master test kit instructions, via retailer. vitamingrocer.com.au Used for API nitrate reading as the NO3 ion ("total nitrate") and phosphate as PO4.
  7. Standard — APHA / AWWA / WEF, Standard Methods, Methods 4500-NO3, 4500-NH3 and 4500-P. Used for the standard reporting of nitrate, ammonia and phosphorus as N and P.
  8. Government — US EPA, "Indicators: Phosphorus". Used for phosphorus in natural waters being reported as total phosphorus (P).
  9. Reference — Haynes (ed.), CRC Handbook of Chemistry and Physics. Used for the standard atomic weights behind the molar-mass cross-checks: N 14.007, P 30.974, O 15.999, H 1.008, giving NO3 62.004, PO4 94.970, NH3 17.031 and NH4+ 18.039.

Related tools