Reef Trace Element Calculator

Volume units

Water in the tank, after rock and sand

Worked example: a 100-gallon reef (378.5 L) with potassium at 360 ppm needs 33.7 g of potassium sulfate to reach 400 ppm (28.9 g of potassium chloride instead). The same tank needs 0.09 mL of 5% Lugol's solution (about 2 drops) to raise iodine from 0.03 to 0.06 ppm, and 2.30 g of strontium chloride hexahydrate to raise strontium from 6 to 8 ppm. Formulae from molar masses in the CRC Handbook of Chemistry and Physics: element mg = rise × litres; K₂SO₄ g = K mg ÷ 448.7; KCl g = K mg ÷ 524.5; Lugol's mL = I mg ÷ 126.4; SrCl₂·6H₂O g = Sr mg ÷ 328.6.

Your trace-element dose

Enter your volume, element and measured levels — the weighed dose (or millilitres of supplement) appears here.

Why use this calculator?

  • Turns a measured shortfall into a weighed dose — potassium, iodine and strontium in one place.
  • Counts iodine in drops, not just millilitres, because a 0.09 mL dose cannot be measured any other way.
  • Shows the potassium chloride alternative, so you can keep chloride and sulfate in balance.
  • Works with commercial supplements too — the strength comes from the label you hold, never assumed.
  • Doses only to a shortfall you measured — it never suggests a target level.

Check the rest of the water with the Water Parameter Checker, dose the big three with the Reef Dosing Calculator (Alk / Ca / Mg), and your tank size with the Tank Volume Calculator. · Back to Saltwater & Reef

Work out how much DIY salt — or how many millilitres of a commercial supplement — closes a measured shortfall in potassium, iodine or strontium. Worked example: a 100-gallon reef with potassium at 360 ppm needs 33.7 g of potassium sulfate to reach 400 ppm. Dose only to a shortfall you measured. Everything runs in your browser; nothing is saved.

How it works

Trace elements are the small numbers: potassium near 400 ppm, strontium near 8 ppm, iodine near 0.06 ppm. Regular water changes replace most of them, so dosing mainly matters in heavily stocked SPS tanks — and only to a shortfall you actually measured. This tool turns that shortfall into a weighed dose of DIY salt, or millilitres of a commercial supplement at the strength on its label.

Element needed (mg) = rise (ppm) × litres. Because 1 ppm is 1 mg per litre, the milligrams of the element itself are the rise times the litres.

Potassium: K₂SO₄ (g) = K mg ÷ 448.7; KCl (g) = K mg ÷ 524.5. One gram of potassium sulfate carries 448.7 mg of potassium (44.87% by weight) and one gram of potassium chloride carries 524.5 mg (52.45%), from their molar masses (K₂SO₄ 174.26, KCl 74.55, K 39.10). Dividing the milligrams needed by the milligrams per gram gives the grams to weigh.

Iodine: Lugol's (mL) = I mg ÷ 126.4; drops = mL × 20. A 5% Lugol's solution carries about 126.4 mg of iodine per mL, so iodine doses come out in fractions of a millilitre — counted in drops, at about 20 drops per mL, because a 0.09 mL dose cannot be measured any other way.

Strontium: SrCl₂·6H₂O (g) = Sr mg ÷ 328.6. One gram of strontium chloride hexahydrate carries 328.6 mg of strontium (32.86% by weight, from SrCl₂·6H₂O 266.62 and Sr 87.62).

Commercial supplement (mL) = rise × (gallons ÷ 100) ÷ label ppm per mL per 100 gal. The label strength is never assumed — it comes from the product label you hold. One millilitre raises a 100-gallon tank by the label ppm, so in a smaller tank the same millilitre raises it more, and the dose is smaller. Check it by units: at 100 gallons both forms of the formula agree (40 mL for a 40 ppm rise at label 1), which is why an earlier inverted version of this formula — dividing by the tank size instead of multiplying — hid for so long; it gave 80 mL for a 50-gallon tank where the correct dose is 20 mL. The version above is the corrected one.

Natural seawater, for reference: potassium about 399, strontium about 8, iodine about 0.06 mg per kg (Millero, Chemical Oceanography). The tool never suggests a target — those are the reference levels, not a prescription.

Worked example

A 100-gallon reef (378.5 L) with potassium at 360 ppm, target 400 ppm, DIY potassium sulfate. The same tank also shows the iodine and strontium cases.

Inputs

378.5 L, potassium 360 → 400 ppm, DIY salt.

Formula

K mg = rise × litres. K₂SO₄ g = K mg ÷ 448.7. KCl g = K mg ÷ 524.5.

Calculation

K mg = 40 × 378.54 = 15,142 mg. K₂SO₄ = 15,142 ÷ 448.7 = 33.7 g. KCl alternative = 15,142 ÷ 524.5 = 28.9 g.

Result

33.7 g of potassium sulfate (or 28.9 g of potassium chloride) to raise potassium from 360 to 400 ppm.

The same tank needs 0.03 × 378.54 = 11.36 mg of iodine to go from 0.03 to 0.06 ppm, which is 11.36 ÷ 126.4 = 0.09 mL of 5% Lugol's — about 2 drops. For strontium from 6 to 8 ppm it needs 2 × 378.54 = 757 mg, which is 757 ÷ 328.6 = 2.30 g of strontium chloride hexahydrate. As a commercial supplement at a label strength of 1 ppm per mL per 100 gal, the potassium case is 40 × (100 ÷ 100) ÷ 1 = 40 mL; at 0.5 ppm per mL it is 80 mL, and in a 50-gallon tank at label 1 it is 20 mL.

How to read your results

The verdict word is the dose — grams of DIY salt, millilitres (and drops) of Lugol's, or millilitres of supplement. Under it, the pair line gives the element and the rise, and the stat grid shows the milligrams of element needed, the rise in ppm, and the alternative salt where one exists.

If the verdict says "No dose needed", the element is already at or above your target — do not dose to push it higher. A "Caution" row means retest a day later before dosing any more: guessing with trace elements causes more trouble than a shortage. For iodine it also means measure in single drops, dilute each drop in tank water first, and dose far from corals. An "OK" row is a check that passed, such as the alternative salt that keeps chloride and sulfate in balance.

For potassium, a 50:50 split of the two salts by potassium keeps chloride and sulfate close to natural seawater — the tool shows the chloride alternative so you can split the dose.

Common mistakes

  • Dosing without a test. Trace elements should only be dosed to a measured shortfall — guessing causes more trouble than a shortage, especially with iodine.
  • Measuring Lugol's by the millilitre. A 0.09 mL dose is about 2 drops — use drops, dilute each one in tank water first, and dose far from corals.
  • Using agricultural potassium products. They can carry heavy metals — use lab or food-grade salts, and dissolve dry salt in RO water before adding it to the tank.
  • Dosing trace elements when water changes would do. Regular water changes replace most trace elements; dosing mainly matters in heavily stocked SPS tanks on two-part or a calcium reactor.
  • Guessing a commercial supplement's strength. The label strength is never assumed — if it is not on the label, this tool cannot work out the millilitres.
  • Using only one potassium salt forever. Potassium sulfate alone piles up sulfate; potassium chloride alone piles up chloride — a 50:50 split by potassium keeps both near natural seawater.

Dose per step of rise

Grams (or millilitres of Lugol's) per step of rise, by system size. All figures recomputed with the formulae above.

Tank sizeK₂SO₄ / 10 ppm KKCl / 10 ppm KSrCl₂·6H₂O / 1 ppm SrLugol's / 0.01 ppm I
25 gal2.1 g1.8 g0.29 g0.007 mL
50 gal4.2 g3.6 g0.58 g0.015 mL
75 gal6.3 g5.4 g0.86 g0.022 mL
100 gal8.4 g7.2 g1.15 g0.030 mL
150 gal12.7 g10.8 g1.73 g0.045 mL
200 gal16.9 g14.4 g2.30 g0.060 mL

Read it as a scaling check: multiply the row for your tank size by the rise you need, in steps of 10 ppm of potassium, 1 ppm of strontium or 0.01 ppm of iodine.

FAQ

Do I need to dose trace elements at all?

Usually not. Regular water changes replace most trace elements, and dosing mainly matters in heavily stocked SPS tanks on two-part dosing or a calcium reactor. If your tests read in range, the answer is no dose — and this tool will say so.

Why is the iodine dose counted in drops?

Because it is so small: raising a 100-gallon tank from 0.03 to 0.06 ppm takes 0.09 mL of 5% Lugol's, about 2 drops. No syringe measures 0.09 mL reliably, so the tool counts drops (about 20 per mL) and the page warns you to dilute each drop in tank water first and dose far from corals.

Potassium sulfate or potassium chloride?

Both deliver the same potassium — 33.7 g of sulfate or 28.9 g of chloride for a 40 ppm rise in 100 gallons. The difference is the other half of the salt: sulfate alone piles up sulfate, chloride alone piles up chloride. A 50:50 split of the two salts by potassium keeps chloride and sulfate close to natural seawater.

How do commercial supplements work here?

You enter the strength from the product label — ppm raised per mL per 100 gallons — and the tool works out the millilitres. The strength is never assumed: if it is not on the label, the tool cannot work out the dose, and it says so instead of guessing.

What are the natural seawater levels?

About 399 ppm potassium, about 8 ppm strontium and about 0.06 ppm iodine (Millero, Chemical Oceanography). Those are reference levels, not targets the tool prescribes — dose only to a shortfall you measured.

Why retest a day later?

Because guessing with trace elements causes more trouble than a shortage, and iodine in particular overdoses fast. Dose, wait a day, retest, and only then decide whether more is needed.

Sources

  1. Textbook — Haynes (ed.), CRC Handbook of Chemistry and Physics. Molar masses used for the element contents: K₂SO₄ 174.26, KCl 74.55, SrCl₂·6H₂O 266.62, K 39.10, Sr 87.62, I 126.90, KI 166.00. Used for the 448.7, 524.5, 328.6 and 126.4 divisors.
  2. Textbook — Millero, F. J., Chemical Oceanography, CRC Press. Natural seawater levels: potassium about 399 mg/kg, strontium about 8 mg/kg, iodine about 0.06 mg/kg. Used for the reference levels in the text and the FAQ.
  3. Hobby practice — Holmes-Farley, R., Reefkeeping Magazine / Advanced Aquarist. Potassium, iodine and strontium in reef tanks, and the use of Lugol's solution. Used for the cautions about dosing only to a measured shortfall and retesting a day later.

No web link is given for these sources because none is on file — the figures come from the printed references named above.

Related tools