Sump Size & Drain-Down Safety Calculator

Inches of display water above the overflow / siphon break — measure from the normal water line down to the overflow teeth or the siphon break, whichever is lower
How much water is normally in the sump while the system runs
Safety margin
For the 20–30% rule-of-thumb comparison only — never the calculation
Footprint of the sump you plan to buy — for the stand-fit check
Footprint of the sump you plan to buy — for the stand-fit check
Inside of your stand — if left blank, the fit check uses the display footprint instead
Inside of your stand — if left blank, the fit check uses the display footprint instead

Drain-down (gal) = display length (in) × width (in) × drop (in) ÷ 231. Minimum sump = normal operating volume + drain-down, plus a 5% or 10% safety margin. The 20–30% of display volume figure is a rule of thumb from reef guides — a sanity check only, never the calculation. Reef / saltwater tool: the drain-down flood is the number-one reef flood cause when the return pump stops.

How big a sump do you need?

Enter your display length, width, drop and operating volume — the minimum sump size appears here, with the drain-down, the margin, and whether the sump fits your stand.

Why use this calculator?

  • Size the sump from your tank’s real drain-down, not a percentage guess — so a power cut does not flood the floor.
  • See exactly how much water drains when the return pump stops, before you buy the sump.
  • Check whether the sump fits inside your stand before it arrives.
  • Know how much margin you have above the bare minimum — and why baffles and equipment eat into it.

Work out the drop from your own tank with the Evaporation & Top-Off Planner, or find your tank’s volume with the Tank Volume Calculator. · Back to Tank Size & Setup

Work out the minimum sump size for your reef tank from your own tank's drain-down — the water that flows back when the return pump stops — plus your normal operating volume and a safety margin. A sump sized this way is what stands between a power cut and a flooded floor. Everything runs in your browser; nothing is saved.

How it works

Drain-down. When the return pump stops, the display water above the overflow (or above the siphon break, whichever is lower) drains back into the sump. That volume is the drain-down: display length (in) × width (in) × drop (in) ÷ 231, because 1 US gallon is 231 cubic inches. The drop is the inches of display water above the overflow — measure it from the normal water line down to the overflow teeth or the siphon break, whichever is lower.

Minimum sump. Minimum sump = normal operating volume + drain-down. The operating volume is how much water is normally in the sump while the system runs. Then add a 5% or 10% safety margin on top. The method comes from Reef2Reef forum threads, where the rule is repeated the same way every time: your sump must hold all the water that drains when the pumps are off.

The 20–30% figure is not the calculation. Reef guides often say a sump should be 20–30% of the display volume. That is a sanity check only, shown here for comparison — the number above comes from your measured drop, and wins when the two disagree.

What it does not do. The formula assumes a rectangular display footprint, so bow-front or irregular tanks drain a different volume. Baffles, skimmer, heater and other equipment displace volume inside the sump, so a sump rated at exactly the recommended volume holds less usable water. Water in the return line above the siphon break also drains — if there is no siphon break, more water drains than the drop alone measures. Always test by unplugging the return pump and watching the sump level before trusting any number here.

Worked example

A 48 × 18 in display, a 1 in drop, 10 gal of normal operating volume, and a 10% safety margin.

Inputs

Display 48 × 18 in. Drop 1 in. Operating volume 10 gal. Margin 10%.

Formula

Drain-down = length × width × drop ÷ 231. Minimum sump = operating volume + drain-down, then + margin.

Calculation

Drain-down = 48 × 18 × 1 ÷ 231 = 3.74 gal. Minimum = 10 + 3.74 = 13.74 gal. With margin: 13.74 × 1.10 = 15.11 gal.

Result

Minimum sump 15.11 gal with the 10% margin. With a 5% margin instead, 13.74 × 1.05 = 14.43 gal.

The same tank with a 2 in drop drains twice as much — 7.48 gal — and needs a 19.23 gal sump at 10% margin. The drop is the number that moves the answer most, which is why it has to be measured on your own tank, not guessed.

How to read your results

The verdict word is the minimum sump size with your safety margin. Under it, the pair line shows the drain-down plus the operating volume and the margin you picked. The stat grid shows the three numbers that make it up: drain-down, operating volume, and the minimum before the margin.

If you entered a sump footprint, the fit check says whether it fits your stand's inside measurements — or the display footprint, if you left the stand blank. A sump that holds enough water but does not fit the stand is no use, and the fit check only covers the footprint: check the height and the door opening too.

The Caution rows are the two things that shrink usable volume: baffles and equipment displacing water, and a missing siphon break letting extra water drain back. Neither changes the number — both mean you should size up, or test the real thing by unplugging the pump.

What to do next: buy a sump rated above the number, check the manufacturer's usable volume rather than its total rating, and run the unplug test before you trust it.

Common mistakes

  • Guessing the drop. A guessed drop gives a guessed answer — measure from the water line to the overflow teeth or the siphon break, whichever is lower.
  • Using the 20–30% rule as the calculation. It is a sanity check from reef guides, not a measurement of your tank.
  • Forgetting that baffles and equipment displace volume. A sump rated at exactly the recommended number holds less usable water than the number says.
  • Skipping the siphon break. Without one, water above the break drains back too — more than the drop alone measures.
  • Checking the footprint but not the height or the door opening. A sump that fits on paper still has to go in.
  • Trusting the number without the unplug test. Unplug the return pump and watch the sump level — that is the real test.
  • Applying the formula to a bow-front or irregular tank. The arithmetic assumes a rectangular display footprint.

Drain-down by drop

Drain-down in gallons for a 48 × 18 in display at different drops — the same arithmetic the calculator runs (48 × 18 × drop ÷ 231).

DropDrain-down
0.5 in1.87 gal
1 in3.74 gal
1.5 in5.61 gal
2 in7.48 gal

Double the drop, double the drain-down. On a bigger display the same drop drains more — a 72 × 24 in display at a 1 in drop drains 7.48 gal, the same as this display at 2 in.

FAQ

What is drain-down?

The display water above the overflow (or siphon break) that flows back into the sump when the return pump stops. It is the water your sump has to absorb in a power cut.

Why not just use 20–30% of the display volume?

That rule is a sanity check from reef guides, not a measurement. Two tanks of the same volume can have very different drops — the drain-down formula uses your tank's own measurements, so it wins when the two disagree.

How do I measure the drop?

With the system running, measure from the normal water line down to the overflow teeth or the siphon break, whichever is lower. That is the inches of water that will drain.

What happens if the sump is too small?

In a power cut or a pump stop, the sump overflows onto the floor. That is the number-one reef flood cause — which is why the margin exists and why the unplug test matters.

Does the operating volume include the skimmer chamber?

It is the total water normally in the sump while the system runs — all chambers together. Baffles and equipment sit in that water and displace some of it, so the usable volume is less than the rating.

Does this work for a bow-front tank?

Not exactly — the formula assumes a rectangular display footprint. A bow-front or irregular tank drains a different volume for the same drop, so measure the drop on your own tank and run the unplug test.

Sources

  1. Reef2Reef — "Tank to sump ratios" thread (forum method: operating volume + drain-down + 5–10% margin) — reef2reef.com (Hobby practice).
  2. Reef2Reef — "Adequate sump size for 90 gallon" thread (forum method) — reef2reef.com (Hobby practice).
  3. Sea Life Planet — aquarium sump size calculator and guide — sealifeplanet.com (Hobby practice).
  4. AquariumSlab — how to calculate aquarium sump size (10% / 20–30% rules) — aquariumslab.com (Hobby practice).

Related tools