RO/DI Water Mixing Calculator

Measure
Volume units
GH in dGH or TDS in ppm — whichever measure you picked
Usually ~0 — enter the measured value if your membrane is ageing
Must sit between the RO and tap readings

Tap fraction = (target − RO) ÷ (tap − RO). GH and TDS do not convert into each other — use one measure for all three readings. Mix the batch before the water change and test the mixed water, not the tap, before it goes in the tank.

Your mix

Enter your tap and RO readings and a target — the tap/RO split appears here, with the volumes in litres and gallons.

Why use this calculator?

  • Hit soft-water targets without guessing — the exact tap/RO split for the hardness you want.
  • Mix a batch before the water change — no adjusting the tank after the fact.
  • Stop swinging parameters — the same ratio every week keeps the water steady.

Check the result against your species' needs with the Water Parameter Checker, confirm your tank size with the Tank Volume Calculator, and convert saltwater readings with the Salinity Converter. · Back to Water Chemistry

Enter your tap and RO readings and a target, and get the exact tap/RO split for the batch — hit soft-water targets without guessing. Everything runs in your browser; nothing is saved.

How it works

The mix is dilution arithmetic. The tap share is how far the target sits between the RO reading and the tap reading:

Tap fraction = (target − RO) ÷ (tap − RO). Tap volume = fraction × total volume. RO volume = total − tap volume.

All three readings must use the same measure — GH in dGH, or TDS in ppm. GH and TDS do not convert into each other, so the tool never mixes them. Pick one measure and use it for the tap, the RO water and the target.

The same share applies to every mineral in the water, so the blend's other readings fall by the same proportion. At a 50% tap share, a tap at 8 dKH and 350 ppm TDS blends to 4.0 dKH and 180 ppm when the RO side reads 0 dKH and 10 ppm TDS (0.5 × 8 + 0.5 × 0 = 4.0; 0.5 × 350 + 0.5 × 10 = 180).

Mixing can only land between the RO and tap readings. A target above the tap reading cannot be reached by mixing — add minerals instead (see the GH/KH Remineralisation Calculator). A target below the RO reading means the RO unit needs servicing. Blending also cuts KH by the same share as GH, and lower KH means lower pH at the same CO₂ — halving KH drops pH by roughly 0.3.

Mix the batch in a bucket or barrel before the water change: blend it, dechlorinate the tap portion, and bring the batch to tank temperature before it goes in. RO water on its own has almost no minerals, so if the mix comes out at or near straight RO, remineralise it for the fish and plants that need GH and KH rather than using it bare.

Worked example

Halving GH for a 20-litre batch: tap water at 12 dGH, RO water at 0 dGH, target 6 dGH.

Inputs

Tap 12 dGH · RO 0 dGH · Target 6 dGH · Total 20 L.

Formula

Tap fraction = (6 − 0) ÷ (12 − 0). Tap volume = fraction × 20 L. RO volume = 20 L − tap volume.

Calculation

Tap fraction = 6 ÷ 12 = 0.5. Tap = 0.5 × 20 = 10.0 L. RO = 20 − 10 = 10.0 L. Ratio 1 : 1. In gallons, 10.0 L = 2.64 gal each (20 L = 5.28 gal).

Result

10.0 L tap + 10.0 L RO — 50% tap / 50% RO for 20 litres at 6 dGH.

Two more checks from the same formula. TDS: tap 300 ppm, RO 0 ppm, target 150 ppm, 40 L — fraction 0.5 again, so 20 L tap + 20 L RO. Imperfect RO: tap 8 dGH, RO 1 dGH, target 4 dGH, 100 L — fraction = (4 − 1) ÷ (8 − 1) = 3 ÷ 7 ≈ 0.43, so 42.9 L tap + 57.1 L RO. Enter the RO water's real reading when the membrane is ageing; assuming 0 when it reads 1 throws the mix off.

How to read your results

The headline is the mix itself — litres of tap plus litres of RO — and the line under it gives the tap share and the total volume at your target reading. The stat grid breaks it out: tap water in litres (with gallons underneath), RO water the same way, and the tap share with the ratio (1 : 1 means equal parts).

Two edge cases have their own messages. Target equals the tap reading: no RO needed for this batch — if the tap already hits what your fish need, the RO unit can stay off. Target equals the RO reading: use straight RO, and remineralise it rather than using it bare.

Use the same ratio every week. A steady blend keeps parameters still; a different ratio each change swings them.

Common mistakes

  • Mixing measures — a GH tap reading with a TDS target. GH and TDS are different numbers; the tool takes one measure for all three readings.
  • Setting a target outside the tap–RO range. No mix can make water harder than the tap or softer than the RO.
  • Using the tank's label gallons instead of the actual water volume. Measure the batch you are mixing, not the sticker on the glass.
  • Forgetting to dechlorinate the tap portion. The RO side needs no conditioner, but the tap water in the blend does — dose for the tap portion only.
  • Moving a stocked tank to much softer water in one change. Shift the blend a little at each water change over several weeks, not all at once.
  • Trusting an old tap reading. Tap water changes with the season and the supplier's source — re-test every month or two, and test the RO water whenever the unit is serviced.
  • Using straight RO water without remineralising. It has almost no minerals; fish and plants that need GH and KH suffer in it bare.

Shrimp TDS targets

Tap share for common shrimp TDS targets, for a 10 US gallon batch from tap water at 350 ppm TDS and RO water at 10 ppm TDS. Each row is the same formula as the worked example.

TargetTap waterRO waterRatioTap share
120 ppm — Caridina3.24 gal6.76 gal1 : 2.132%
150 ppm — soft-water fish4.12 gal5.88 gal1 : 1.441%
200 ppm — Neocaridina5.59 gal4.41 gal1 : 0.856%
250 ppm — community7.06 gal2.94 gal1 : 0.471%

FAQ

Can I mix by GH and check the TDS too?

Yes — the same tap share applies to every mineral. At a 50% tap share, a tap at 8 dKH and 350 ppm TDS blends to 4.0 dKH and 180 ppm when the RO side reads 0 dKH and 10 ppm TDS. This tool calculates one measure at a time, so run it once per measure if you want both numbers.

Why can't I reach my target?

Mixing only lands between your two readings. Above the tap reading, you need to add minerals rather than mix — try the GH/KH Remineralisation Calculator. Below the RO reading, the RO unit needs servicing; a tired membrane or exhausted DI resin lets the RO reading creep up.

Does mixing RO water lower the pH?

Yes, gently. Blending cuts KH by the same share as GH, and lower KH means lower pH at the same CO₂ — halving KH drops pH by roughly 0.3. That is why RO mixing is the gentle way to soften water for soft-water fish, rather than a sudden chemical adjustment.

My RO water reads above 0 — is that normal?

Fresh RO/DI water reads 0–10 ppm TDS, and RO without DI often reads 5–20 ppm. Enter the real reading instead of assuming 0. If the RO reading climbs above roughly 10% of the tap TDS, the membrane or DI resin needs attention.

Can I use distilled water or rainwater instead of RO?

Yes — the same maths applies; enter its reading as the RO value. Distilled water reads near 0. Rainwater can carry dust and roof contaminants, so collect it away from metal roofs and test it before use.

Do I still need dechlorinator?

For the tap portion, yes — dose for the tap water in the blend only. RO water itself needs none: the carbon prefilter removes chlorine before the membrane. If your meter reads conductivity rather than TDS, convert it first with the TDS/Conductivity Converter.

Sources

  1. Standard — APHA/AWWA/WEF, Standard Methods, Methods 2340 (Hardness), 2320 (Alkalinity), 2540 (Solids). Hardness and alkalinity expressed as CaCO₃; TDS in mg/L. Used for the units the three readings share.
  2. Government — USGS, Hardness of Water. Typical hardness of tap water across the US. Used for the tap-water context — why tap readings vary by place and season.
  3. Method — linear mass balance of dissolved constituents. A blend's concentration is the volume-weighted average of its sources, valid when both readings use the same unit. This is the formula the tool runs.

Related tools